813309

Westfire WF44 Manual

9
Zoom out
Zoom in
Previous page
1/30
Next page
WESTFIRE · WF 44 · WF 45 · WF 46 WESTFIRE · WF 44 · WF 45 · WF 46
9
UK
WESTFIRE · WF 44 · WF 45 · WF 46
UNIQ 44 UNIQ 45 / UNIQ 46
Height 736 mm 950 mm
Width 477 mm 477 mm
Depth 374 mm 374 mm
Closed combustion yes Yes
WESTFIRE · WF 44 · WF 45 · WF 46
UNIQ 44 / UNIQ45 / UNIQ46 dimensions
STOVE PERFORMANCE & TESTING
Westfire UNIQ44/ UNIQ45/ UNIQ46 have been approved in accordance with EN 13240
PREPARATORY WORK AND SAFETY CHECKS
IMPORTANT WARNING
This stove must not be installed into a chimney that serves any other heating appliance. There must not be an extrac-
tor fan fitted in the same room as the stove as this can cause the stove to emit fumes into the room.
Chimney
Chimney Connection: Flue Diameter 125 mm
IMPORTANT: Once the stove is unpacked and checked it is necessary to remove the central bar from the flue collar of
the stove before installation. To remove unbolt collar remove bar and replace collar.
In order for the stove to perform satisfactorily the chimney height must be sufficient to ensure an adequate
draught so as to clear the products of combustion and prevent smoke problems into the room.
Minimum draft: UNIQ44/ UNIQ45/ UNIQ46 stoves has been tested with a draft of
12 Pa. Maximum draft 25 Pa.
Flue gas flow 4.5 g/sec.
Flue gas temperature 249°C. approximately 12 Pa.
NOTE: A chimney height of not less than 4.5 metres measured vertically from the outlet of the stove to the top of the
chimney should be satisfactory. Alternatively the calculation procedure given in BS 5854:1980 may be used as the
basis for deciding whether a particular chimney design will provide sufficient draught.
The outlet from the chimney should be above the roof of the building in accordance with the provisions of Building
Regulations Approved Document J.
If installation is into an existing chimney then it must be sound and have no cracks or other faults which might
allow fumes into the house. Older properties, especially, may have chimney faults or the cross section may be
too large i.e. more than 160 mm x 160 mm. Remedial action should be taken, if required, seeking expert advice,
if necessary. If it is found necessary to line the chimney then a flue liner suitable for solid fuel must be used in
accordance with Building Regulations Approved Document J.
Any existing chimney must be clear of obstruction and have been swept clean immediately before installation of
the stove. If the stove is fitted in place of an open fire then the chimney should be swept one month after instal-
lation to clear any soot falls which may have occurred due to the difference in combustion between the stove and
the open fire.
Stove model Weight
Nominal heat output
Wood Smokeless fuels
UNIQ 44 80 kg 5.0 KW N/A
UNIQ 45 / UNIQ 46 90 kg 5.0 KW N/A
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Westfire WF44 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Westfire WF44 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 1.14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info