813317

Westfire WF35 Manual

8
Zoom out
Zoom in
Previous page
1/32
Next page
WESTFIRE · WF35
8
UK
Model choice UNIQ 35 Standard UNIQ 35 PEDESTAL UNIQ 35 Inset
50mm base 400mm pedestal 3 sided frame 4 sided frame
Closed combustion Yes Yes Yes Yes
Flue gas flow rate wood /coal Test flue gas temperature wood /coal @ pascals of pressure
UNIQ 35 4.6/ 4.7g/sec 259/240c 12
Stove model Efficiency Weight Nominal heat output CO@ 13% 02
Wood/coal Wood Smokeless fuels Wood/coal
UNIQ 35 standard 78%/76% 80kg 4.6 KW 3.7 KW .12/.17
UNIQ 35 pedestal 78%/76% 110kg 4.6 KW 3.7 KW .12/.17
WESTFIRE UNIQ 35
STOVE PERFORMANCE & TESTING
Westfire Uniq 35 models have been approved in accordance with EN 13240.
PREPARATORY WORK AND SAFETY CHECKS – IMPORTANT WARNING
IMPORTANT WARNING
This stove must not be installed into a chimney that serves any other heating appliance.
There must not be an extractor fan fitted in the same room as the stove as this can cause the stove to emit fumes
into the room.
Chimney – Chimney Connection
Flue Diameter 125mm
In order for the stove to perform satisfactorily the chimney height must be sufficient to ensure an adequate
draught so as to clear the products of combustion and prevent smoke problems into the room.
NOTE: A chimney height of not less than 4.5 metres measured vertically from the outlet of the stove to the top of
the chimney should be satisfactory. Alternatively the calculation procedure given in BS 5854:1980 may be used as
the basis for deciding whether a particular chimney design will provide sufficient draught.
The outlet from the chimney should be above the roof of the building in accordance with the provisions of Build-
ing Regulations Approved Document J.
If installation is into an existing chimney then it must be sound and have no cracks or other faults which might
allow fumes into the house. Older properties, especially, may have chimney faults or the cross section may be too
large i.e. more than 160 mm x 160 mm. Remedial action should be taken, if required, seeking expert advice. If
it is found necessary to line the chimney then a flue liner suitable for solid fuel must be used in accordance with
Building Regulations Approved Document J.
Any existing chimney must be clear of obstruction and have been swept clean immediately before installation of
the stove. If the stove is fitted in place of an open fire then the chimney should be swept one month after instal-
lation to clear any soot falls which may have occurred due to the difference in combustion between the stove and
the open fire.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Westfire WF35 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Westfire WF35 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 1.44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info