784849

Wellis Easy 7 Manual

11
Zoom out
Zoom in
Previous page
1/108
Next page
9
SETTING FILTER
OR PURGE CYCLE
FREQUENCY
The display will show FFxx,
“xx” representing the number
of cycles per day. Use the Up
or Down key to adjust the
frequency. Use the Light key to
jump to the next parameter,
economy mode (EP).
The “Filter cycle” indicator
lights up when filter is on and
flashes when suspended.
SETTING FILTER
CYCLE DURATION
(not available on purge
systems)
The display will show Fdxx,
“xx” representing the dura-tion
in hours of the filter cycle. Use
the Up or Down key to adjust
the duration. Use the Light key
to jump to the next parameter,
filter or purge frequency (FF).
0 = no filtration
24 = continuous filtration
It is not recommended to set
this to "0".
PROGRAMMING STEPS
PROGRAM
MENU
The program menu is accessible
by holding down the Light key
for 5 seconds. In the program
menu the following parameters
can be set: clock, the filter or
purge cycles, economy mode
and temperature units. While
you are in the program menu,
use the Up or Down key to
adjust the parameters and use
the Light key to jump to the
next parameter.
The changes will be saved after
the confirmation of the last
parameter only. If there is no
action taken for 10 seconds, the
system will exit the program
menu without saving any
changes.
SETTING THE
CLOCK
Enter the program menu by
holding down the Light key
for 5 seconds. The display will
show the current clock setting
with the hour flashing.
Depending on factory settings
your system may be set to 24-
hour time or 12-hour time.
Setting the hour: Use the Up
or Down keys to adjust the
hours. Press the Light key to
jump to the next parameter,
the minutes.
Setting the minutes: Use the
Up or Down keys to adjust the
minutes. Press the Light key to
jump to the next parameter,
the filter or purge start time
(FS).
SETTING FILTER
OR PURGE CYCLE
START TIME
The display will show FSxx, “xx”
representing the starting hour
of the cycle. Use the Up or Down
key to adjust the hours. Use the
Light key to jump to the next
parameter, filter duration (Fd).
PROGRAMMING
THE FILTER/ PURGE
CYCLES
Depending on system config-
uration your spa will perform
either a filter or a purge cycle.
The filter cycle menu consists
of the following parameters:
the start time (FS), the duration
(Fd) and the frequency (FF).
The purge cycle menu consists
of the following parameters:
the start time (FS) and the
frequency (FF).
A filter cycle consists of start-
ing all the pumps and blower
in high speed for 1 minute
(purge step) then, the pump
associated with the filter
will run in low speed for the
remaining duration of the
filter cycle (clean step).
A purge cycle is used when
the spa is equipped with a 24
hour circulation pump which
provides a continuous clean
step. It consists of starting
all the pumps and blower in
high speed for 1 minute.
USER INTERFACE  EASY 4
SETTING ECONOMY
MODE
This mode allows you to lower
the temperature set point of
the spa by 20 °F (11 °C) during a
certain period of the day.
The display will show EPx, “x”
representing the state of the
programmed economy (0 =
disabled, 1 = enabled). Use
the arrow keys to enable or
disable economy mode. Use
the Light key to jump to the
next parameter, economy start
time (ES).
Note that the parameters for the economy mode settings are
associated to specific low level configuration of the system that are
not present in all software revisions.
SETTING ECONOMY
START TIME
The display will show ESxx,
“xx” representing the hour at
which the economy mode will
become active. Use the Up or
Down key to adjust the hour.
Use the Light key to jump to
the next parameter, economy
duration (Ed).
When the Economy mode is ON,
the display will toggle between
the “Eco” message, the time,
and the water temperature.
SETTING ECONOMY
DURATION
The display will show Edxx, “xx”
representing the duration in
hour of the economy mode. Use
the Up or Down key to adjust
the hour. Use the Light key to
jump to the next parameter,
temperature unit.
24 = continuous economy
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wellis Easy 7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wellis Easy 7 in the language / languages: English as an attachment in your email.

The manual is 11.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wellis Easy 7

Wellis Easy 7 User Manual - German - 124 pages

Wellis Easy 7 User Manual - Dutch - 113 pages

Wellis Easy 7 User Manual - French - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info