784851
88
Zoom out
Zoom in
Previous page
1/108
Next page
CHEMICAL TREATMENT DEVICE
THINGS TO KNOW ABOUT THE ASIN AQUA
The CHEMICAL TREATMENT device provides pure sparkling
water that contains only a minimal amount of chemical
substances. This system directly measures and monitors
free chlorine content and the redox potential of the spa
water. The CHEMICAL TREATMENT device regulates the
spa water while using only a minimal amount of chlorine,
thus eliminating the strong smell of overtreated water. The
touch screen solution allows you to attentively monitor the
measuring units and regulations of your spa. The CHEMICAL
TREATMENT device uses the current filtration equipment of
the spa and works with a timed dosing system and even with
chlorine-free oxygen based disinfection.
HEALTH AND SAFETY
The CHEMICAL TREATMENT device makes it possible to
adhere to the rules of hygiene in regards to the physical and
chemical demands concerning the spa water’s quality.Do not
open the casing of the CHEMICAL TREATMENT device and
do not change any of its internal parts. Opening the casing
voids the warrantyThe chemicals used by the CHEMICAL
TREATMENT device can only be used in safe conditions to
avoid damage or personal injury. Always use personal protec-
tive equipment (safety goggles and gloves) when handling
pH or chlorine substances. For further information consult
your Chemical Safety Data Sheet.
INSTALLING THE CHEMICAL TREATMENT DEVICE
Install the CHEMICAL TREATMENT device in an environment
free of dust and high humidity. Secure your device on the
wall in a way that leaves at least 30cm of empty space on
either side.
To connect your CHEMICAL TREATMENT device to the water
supply provides a special Speedfit quick connector. To con-
nect push the plastic pipe into the Speedfit quick connector.
To remove the pipe from the quick connector push in the
collet and pull the pipe out.
1. Cut off the plastic pipe at a 90-degree angle to ensure
proper connection. Use a sharp knife or blade for precise
cutting.
2. Connect the water intake on the left and the water outlet
on the right. Ensure that the water pressure does not go
over the 1,5 bar value.
3. The water outlet of the CHEMICAL TREATMENT device can
be connected to the plumbing, before the pump, to the
skimmer, the buffer tank, or the drain pipe.
DISCONNECTING
After connecting to the water supply your ASIN Aqua device
is able to take samples of the spa water and analyze them.
Analysis makes monitoring of chlorine levels and pH values
possible, ensuring the spa's hygiene.
Adjusting the spa’s parameters Every spa represents a unique
solution. Temperature, size, location, and water hardness
all affect the ability of the CHEMICAL TREATMENT device to
monitor and regulate the water of your spa. To reach maximal
performance the CHEMICAL TREATMENT device must be
adjusted to your spa’s characteristics. After selecting the
REQUIRED VALUES menu item:
1. Adjust the filtration parameters of the spa.
2. Adjust the parameters of the water. Adjusting the filtration
parameters The CHEMICAL TREATMENT device must know
the spa's size and filtration cycles. When installing the
CHEMICAL TREATMENT device you must define these spa
parameters:
A.) Choose the SETTINGS menu item on the start screen,
then press the PARAMETERS item to get to the next
screen.
B.) Choose the spa PARAMETERS item
C.) Choose the spa VOLUME menu item.
Your choice is shown by a black triangle. Check the spa’s data
sheet for its volume. (1000L =1m3) Press the + and - buttons
to enter the appropriate spa value, then press OK to save.
Note: If the volume of your spa is between 1000 and 1500 liters,
select 1 m3. If it is between 1500 and 2000 liters, select 2 m3.
D.) Choose the desired disinfection timeframe and press
OK to save. Your choice is shown by a black triangle
at the bottom. The displayed number shows the time-
frame of the disinfection cycle, not its frequency.
OPTIONAL ACCESSORIES  CHEMICAL TREATMENT
86
88


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wellis Aquasoul Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wellis Aquasoul Pro in the language / languages: English as an attachment in your email.

The manual is 11.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wellis Aquasoul Pro

Wellis Aquasoul Pro User Manual - German - 124 pages

Wellis Aquasoul Pro User Manual - Dutch - 113 pages

Wellis Aquasoul Pro User Manual - French - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info