784851
61
Zoom out
Zoom in
Previous page
1/108
Next page
You can choose between four different water regulation
modes available. Your in.grid is automatically detected by the
spa control system at power up. It will be ready to use with
your preferred heat mode one minute following power up.
The relay contacts of the in.grid will be closed if the external
heating system is activated. Otherwise, the relay contacts
are open.
Your desired heat mode must be set by adding a jumper on
one of the five (5) different positions.
*Note: Your heat mode selection can be changed with the
in.touch 2 app on your mobile device. On your app, any new
selection will override the jumper setting of the in .grid. The
in.touch 2 app will automatically detect the in.grid presence and
will adapt its menu configuration as required.
Heat mode
selection
Diagnostic
LED
Heat
LED
Five available heat modes are offered with in.grid:
1- DIS (DISABLED)
Use this mode if the spa configuration does not have any
external heating system and only the single switch func-
tionalities are used. This will avoid in.touch 2 application on
a mobile device to display the Heat Mode Selection menu*.
The spa controller will regulate the water temperature using
the standard resistive heater. The single button switches
will control the different spa accessories according to the AC
jumper selections.
IMPORTANT: This mode can only be set with the heat mode
jumpers.
2- INT (INTERNAL)
This mode provides an easy way to revert back to standard
water regulation using the internal heater in case of problem
with the external heating system.
* This mode can be set with your in.touch 2 app on a mobile
device without the need to open the spa skirt to change the
jumper setting on the in.grid. Thanks to your in.touch 2, it will be
easier to set your preferred heating mode back once the external
heating system is available.
3-EXT (EXTERNAL)
Use this mode for a maximum energy saving purpose. The
spa control system will only use your external heating system
to regulate the water temperature. In normal operation, the
internal heater will never be activated.
* This mode can be set with your in.touch 2 app on a mobile de-
vice without the need to open the spa skirt to change the jumper
setting on the in.grid.
Freeze Protection
Freeze protection has been added because EXT (EXTERNAL)
mode does not allow the activation of the internal heater.
In cold weather, if it becomes impossible to keep the water
over freezing point, the help of the internal heater will then
be needed. This is the only time the freeze protection will
come in.
At any time, if the water temperature drops to 4F (4.5°C),
the resistive heater will give a boost to avoid freezing. The
freeze protection will stay active until water temperature
reaches the minimum allowed set point (usually 59°F / 15°C).
Normal EXT mode will resume functioning thereafter.
4- BOTH (BOTH SYSTEMS ALL AT ONCE)
Use this mode for swim spas or large spas, which have bigger
needs of energy to keep the water temperature at the desired
set point.
The spa control system will always use the external heating
system AND the internal heater simultaneously to regulate
the water temperature; they are both activated or deactivat-
ed at the same time.
* This mode can be set with your in.touch 2 app on a mobile de-
vice without the need to open the spa skirt to change the jumper
setting on the in.grid.
5- SMART (ENERGY SAVINGS)
Use this mode for a better energy saving purpose, combined
with a maximum water temperature regulation efficiency.
The spa control system will always use the external heating
system to regulate the water temperature. If the temperature
falls too far below your set point (-2.5°F), the internal heater
will be activated to help your external heating system reach
the set point.
Once the temperature is within 1.5°F from set point, the in-
ternal heater is deactivated and the external heating system
takes all control of the water regulation again.
* This mode can be set with your in.touch 2 app on a mobile de-
vice without the need to open the spa skirt to change the jumper
setting on the in.grid.
Troubleshooting
DIAGNOSTIC LED
The diagnostic LED will help you with the status of the con-
nection between the spa control system and the in.grid.
Blinking light: Spa control system not detected, not
compatible or in Disable mode if one of your
single switches doesn’t operate properly.
Solid light: Spa control system detected
No light: Power Off
HEAT LED
Solid light: Relay contacts close and external heating
system on.
No light: Relay contacts open and external heating system
off.
OPTIONAL ACCESSORIES  IN.GRID
Heat Mode Operations
59
61


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wellis Aquasoul Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wellis Aquasoul Pro in the language / languages: English as an attachment in your email.

The manual is 11.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wellis Aquasoul Pro

Wellis Aquasoul Pro User Manual - German - 124 pages

Wellis Aquasoul Pro User Manual - Dutch - 113 pages

Wellis Aquasoul Pro User Manual - French - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info