784851
12
Zoom out
Zoom in
Previous page
1/108
Next page
IN.XE ERROR CODES DESCRIPTION
Hr
An internal hardware error has been detected in the in.xe.
Contact dealer or service supplier.
AOH
Temperature inside the spa skirt is too high, causing the internal temperature in the
in.xe to increase above normal limits. Open skirt and wait until error clears.
Prr
A problem is detected with the temperature probe.
Call your dealer or service supplier.
HL
The system has shut the heater down because the temperature at the heater has
reached 119°F (48°C).
Do not enter the water! Remove the spa cover and allow the water to cool down, then shut
power off and power your spa up again to reset the system.
FLO
The system does not detect any water flow while the primary pump is running.
Check and open water valves. Check for water level.
Clean filter. If the problem persists, call your dealer or service supplier.
OH
The water temperature in the spa has reached 108°F (42°C).
Do not enter the water! Remove the spa cover and allow the water to cool down to a lower
temperature.
Call your dealer or service supplier if problem persists.
TROUBLESHOOTING SECTION
Should an error occur, the display will show one of the following error messages toggled with the clock and the water tempera-
ture.
SMART WINTER
MODE
Our Smart Winter Mode pro-
tects your system from the cold
by turning pumps on several
times a day to prevent water
from freezing in pipes.
The “SWM” indicator lights
up when freezing is detected
and flashes when the purge
is active.
SETTING TEMPERA-
TURE UNIT
Water temperature can be
displayed in either Fahrenheit
(°F) or Celsius (°C). The display
will show F or C.
Use the Up or Down key to
change the setting. Use
the Light key to save all the
parameters.
USER INTERFACE  EASY 4
COOLDOWN
After heating the spa water
to the desired Set Point, the
heater is turned off, but its
associated pump (Pump 1
low-speed or CP) remains on
for a predetermined period
of time to ensure adequate
cooling of the heating
element, prolonging its
useful life.
WATER TEMPERA-
TURE REGULATION
Every 15 to 90 minutes the
pump will run to ensure
accurate water temperature
readings as well as avoid heater
activation in dry conditions.
After verifying pump activation
and taking a water temperature
reading if required, the system
automatically turns the heater
on to reach and maintain water
temperature at Set Point.
Indicator flashes when
taking water temperature
reading.
10
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wellis Aquasoul Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wellis Aquasoul Pro in the language / languages: English as an attachment in your email.

The manual is 11.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wellis Aquasoul Pro

Wellis Aquasoul Pro User Manual - German - 124 pages

Wellis Aquasoul Pro User Manual - Dutch - 113 pages

Wellis Aquasoul Pro User Manual - French - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info