579826

Weller WXA 2 Manual

16
Zoom out
Zoom in
Previous page
1/267
Next page
32
GB
Soldering and desoldering
Carry out soldering work as directed in the opera-
ting instructions of your connected soldering tool.
Handling the soldering tips
Coat the selective and tinnable soldering tip with
solder when heating it up for the rst time. This
removes oxide coatings which have formed
during storage and impurities from the soldering
tip.
Make sure that the soldering tip is well coated
with solder during breaks between soldering work
and prior to storage of the device.
Do not use aggressive uxing agents.
Always make sure that the soldering tips are
tted properly.
Select as low a working temperature as possible.
Select the largest possible soldering tip shape for
the application.
Rule of thumb: the soldering tip should be roughly
as large as the soldering pad.
Coat the soldering tip well with solder to ensure
that there is efcient heat transfer between the
soldering tip and the soldering area.
Prior to extended breaks between soldering work,
switch off the soldering system or use the Weller
function to reduce the temperature when the
soldering equipment is not in use.
Coat the tip with solder prior to storage if you do
not intend to use the soldering iron for an
extended period of time.
Apply solder directly to the soldering area, not to
the soldering tip.
Change the soldering tips using the designated
tool.
Do not apply mechanical force to the soldering
tip.
Notice
The control units have been adapted to hold a
medium-sized soldering tip. Discrepancies may
occur if the tip is changed or a different shaped
tip is used.
WX 2, WXD 2, WXA 2: Overload cut-out (255 W)
To avoid overloading a WX station, one channel
is automatically deactivated if the power output
of both tool channels is greater than 255 watt
(Auto-Off).
An overload cut-out will also occur if the following
combinations of tools are connected: e. g.
- 2 WXHP 120 heating plates
- A WXHP 120 heating plate and desoldering iron
WXDP 120 or WXDV 120
Equipotential bonding
a
b
c
d
Four variants are possible by connecting the 3.5 mm jack socket
differently:
a Hard-grounded supplied without plug.
b Equipotential
bonding
with plug, equaliser at centre contact.
c Floating with plug
d Soft-grounded with plug and soldered resistor. Ground-
ed through selected resistor.
For your safety
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Weller WXA 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Weller WXA 2 in the language / languages: All languages as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Weller WXA 2

Weller WXA 2 Quick start guide - All languages - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info