99768
22
Zoom out
Zoom in
Previous page
1/57
Next page
21
10. Use a soldering vapour suction device
If devices for solder vapour suction are available, ensure that these are connected and
correctly used.
11. Do not use the cord for purposes for which it is not designed.
Never carry the soldering tool by the cord. Don't use the cord to pull the power plug
from the socket. Protect the cord from heat, oil, and sharp edges.
12. Protect the work piece.
Use clamping devices to hold the work piece in place. This is more secure than using
your hands, and leaves both hands free to work with the soldering tool.
13. Avoid abnormal posture.
Set-up your work place with proper ergonomics. Avoid bad posture when working.
Always use the suitable soldering tool.
14. Take care of your soldering tool.
Keep the soldering tool clean for better and safer work. Follow the maintenance
instructions and the notices concerning changing the soldering tips. Regularly inspect
all connected cords and hoses. Repairs should only be carried out by a qualified
technician. Use only original WELLER replacement parts.
15. Remove the power plug from the socket before opening the unit.
16. Remove all maintenance tools .
Before switching on the unit, check that all maintenance tools have been removed from
the unit. 17. Avoid unexpected operation.
Make sure that the mains switch is turned off when inserting the plug into the socket or
connecting to mains. Don't hold a soldering tool which is connected to a mains supply
while touching the mains switch.
18. Extension cords outside.
Use only extension cords outside which are authorised and correspondingly labelled.
19. Pay attention.
Be careful of what you do. Work with caution. Don't use the soldering tool if you are not
concentrated on your work.
20. Inspect the soldering tool for any damage.
Before further use of the soldering tool, safety devices or slightly damaged parts must
be carefully checked for error-free and intended operation. Inspect moving parts for
error-free operation and that they don't bind, or whether any parts are damaged. All
parts must be properly mounted and all requirements fulfilled for guaranteed error-free
operation of the soldering tool. Damaged safety devices and parts must be repaired or
replaced by a qualified technician, so long as nothing else is indicated in the Operation
Manual.
21. Attention
Use only accessories or attachments which are listed in the accessories list of the
Operation Manual. Use only WELLER accessories or attachments on original WELLER
equipment. Use of other tools and other accessories can lead to a danger of injury.
22. Repairs to your soldering tool should be carried out by qualified
technician
This soldering tool is in accordance with the relevant safety regulations. Repairs should
only be carried out by a qualified electrician using original WELLER replacement parts.
Failure to do so can lead to accidents for the operator.
23. Do not work on electrically live parts.
The grip of antistatic designed soldering tools is conductive.
24. Applications with other WELLER equipment
If the soldering tool is to be used together with other WELLER equipment and
attachments, also observe the warning notices given in the corresponding Operation
Manual.
25. Observe the valid safety regulations for your work place.
WECP20.pm65 11.03.2002, 11:19 Uhr21
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Weller WECP-20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Weller WECP-20 in the language / languages: Dutch, All languages as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info