686262

Weldkar TIG 1660 DC-HF Pulse DC INVERTER WELDER Manual

18
Zoom out
Zoom in
Previous page
1/48
Next page
INVERTER WELDER WK TIG 1660 DC/HF PULSE
7
6
5
3 4
1
2
8
3. INSTALLATION
This must be carried out by skilled personnel. All
connections must be carried out according to current
regulations, and in full observance of safety laws
(regulation CEI 26-23 – CEI CLC 62081).
- Make sure that the supply voltage matches the
voltage indicated on the specifications plate.
- When mounting a plug, make sure it has an
adequate capacity, and that the yellow/green
conductor of the power supply cable is connected to
the earth pin.
WARNING! Extension cords of up to 30m must have a
crosssection of at least 2.5 mm
2
.
3.1 DESCRIPTION OF THE EQUIPMENT
1) Positive output terminal (+)
2) Negative output terminal (-)
3) TIG torch trigger connector
4) Shielding Gas Outlet (TIG Welding Torch)
5) Power switch: control power through and break
6) Power Access client: access to cable
7) Shielding Gas Inlet
8) Fan: for cooling the machine
9) Process Selection Button
The process selection control is used to select the
desired welding mode. Three modes are available,
MMA (Stick), LIFT TIG and HF TIG modes.
10) 2T or 4T mode selection Button (LIFT TIG
and HF TIG Mode only)
- TIG 2T; In this mode, the torch trigger must remain
depressed.
- TIG 4T; This mode of welding is mainly used for
long welding runs to reduce operator fatigue. In this
mode the operator can press and release the torch
trigger and the output will remain active. To shut off
the arc, the trigger switch must again be depressed
and released, thus eliminating the need for the
operator to hold the torch trigger.
11) Digital Ampère/Volt and parameter display
The digital display is used to display both the pre-set
welding current and welding voltage of the power
source. When welding, the display will show actual
welding current and welding voltage.
It is also used to display Parameters in Programming
Mode. Depending on the Programming Parameter
selected, the status indictor adjacent to the display
will illuminate to show the units of the programming
parameter.
12) THERMAL PROTECTION
The indicator will illuminate if the duty cycle of the
power source has been exceeded.
13) Multifunction Control
The multifunction control knob is used to adjust welding
current. It is also used to adjust parameters when in
programming mode.
14) MMA parameter settings
Press the Process Selection Button (9) to
select MMA modus. Use the multifunctional
control knob (13) to select and adjust the
following parameters:
- HOT START: 0-10
This led lights to indicate that the
display shows the Hot Start setting.
By using the multifunction control
knob (13), this value can be changed.
The welding machine delivers an overcurrent to
improve electrode starting.
- A – Welding Current: 5-160 Ampère
This led lights to indicate that the display shows the
preset welding current. By using the multifunction
control knob (13), the welding current can be
changed.
- ARC FORCE: 0-10
This led lights to indicate that the display shows
the Arc Force setting. By using the multifunction
control knob (13), the setting can be adjusted.
Increasing the Arc Force allows greater penetration
control to be achieved.
15) LIFT TIG en HF TIG parameter settings
These indicator lights will illuminate when programming.
Use the Multi Function Control Knob (13) to adjust the
parameter selected.
18
9 10 11
13
12
14
15
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Weldkar TIG 1660 DC-HF Pulse DC INVERTER WELDER at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Weldkar TIG 1660 DC-HF Pulse DC INVERTER WELDER in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info