Manual Weightec 348 (page 45 of 53) (English)

50963

Zoom out

Zoom in

1/53

11.7 SETPOINT EXECUTIVE CODE TABLE 7

1 = function ON 0 = function OFF

Set

gross

Set

net

Hold

step to next

Hold

Setpoint :

not active

(at receipt)

Setpoint :

immediately

active

(at receipt)

(= if applicable

delete tare)

(= tare to

zero)

(next setpoint

will be set

active)

Code in digit

string

10 of the

”setpoint”

0 0 0 0 @ `

0 0 0 1 A a

0 0 1 0 B b

0 0 1 1 C c

0 1 0 0 D d

0 1 0 1 E e

0 1 1 0 F f

0 1 1 1 G g

1 0 0 0 H h

1 0 0 1 I i

1 0 1 0 J j

1 0 1 1 K k

1 1 0 0 L l

1 1 0 1 M m

1 1 1 0 N n

1 1 1 1 O o

Attention:

1 “Set net” (tare to zero after no motion) en “Set gross” are automatically executed before the started

setpoint’s output is switched to “active “.

2 “Hold” (of the setpoint output) en “Step to next setpoint” are executed automatically after switching off a

setpoint that has achieved its selected weight value.

3 If “Hold” and “Hold + step next” both are selected, the “Hold” is executed after a time delay of 0.3 seconds .

4 If “Set net” and “set gross” both are selected, a “set zero” will be executed instead of a tare operation.

However if zero setting is not possible because of the gross weight value is outside the zero limits (-1,3% . .

+2,7%) , the setpoint will not start up until zero setting is possible.

5 If a setpoint was entered as “not active”, it may be started with a “Run” command (table 8).

6 If the 4

setpoint is selected with “hold + step next”, it will not execute the “step next” function, but will

continuously be compared with the actual gross weight value, independent of an active tare value by “set

net” = net weight reading for the setpoint comparator. The “hold” function however stays active.

Example :

If digit nr. 10 of a transmitted string of one “setpoint” shows the letter a , this means:

this setpoint is active now. If this setpoint is switched “off” digit 10 shows a A.

If digit nr. 10 of a received

command string of one “setpoint” shows the letter F, the 348 waits with starting this

setpoint until a “Run“ command is received. At receipt of this “Run” command the 348 starts no motion

control and, after standstill, it will tare to zero and set the setpoint’s output “on” (in conduction). After achieved

weight value the output is switched “off” en set on “hold” and the next setpoint is started up.

See too chapter 10.4 : communication examples.

Manual 348-2 V 3.1 Page 45 01-06-2007

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Weightec 348 in the language / languages: English as an attachment in your email.

The manual is 1,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Weightec 348

Weightec 348 User Manual - Dutch - 49 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Weightec 348 Manual

Product: