50963
22
Zoom out
Zoom in
Previous page
1/53
Next page
6.2 INTERNAL CALIBRATION DISPLAY
The small dot matrix display on the main print board has 2 lines with 16 alpha numerical characters each.
Setting switch 49 (calibration mode) high will switch on the back lightning and will double the damping of the
weight reading in order to create a very stable reading of the weight value.
After start up (see 6.3) both the gross and net weight values are displayed on the two lines of the display,
with a 10 x higher accuracy.
This makes it possible to adjust a weighing scale with 0.1 scale division accuracy.
Next to the weight values a number of important status reports are shown, as they are sent in the data string too.
Reading:
G : gross weight (x 10)
N : net weight (x 10)
! : A/D converter overload M +/- : weight goes up (+) of down (-): Motion
(value > 55900) S 1 : Standstill within +/- 0.2 scale division
# : calibration mode S 2 : Standstill within +/- 0.1 scale division
(sw.49 “on”) T +/- : Tare operation is in execution
Z +/- : Zero operation is in execution
Z > : Zero value is too big
Z = : Zero value is too big at initial switch on
Z ? : Zero setting is disabled at switch 5 “off”
More info about these digits 11 and 12 on page 30
+ : weight value is positive
- : weight value is negative
: weight value is 0 , + of - 0,1 scale division
( is blank)
/ : weight value is negative > 0,5 scale division
(in legal mode only = switch 60 ON)
! : weight value is > selected overload value
> : input loadcell signal is too high
< : input loadcell signal is too low
More info about these digits 4 and 5 on page 30
The contrast setting of the calibration display may be adjusted by a potmeter.
This potmeter is situated direct under the hole in between switch groups nr. 40 en 41.
Manual 348-2 V 3.1 Page 22 01-06-2007
#
G + 1 5 6 2 , 0 5 S 2
N + 2 0 , 0 0
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Weightec 348 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Weightec 348 in the language / languages: English as an attachment in your email.

The manual is 1,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Weightec 348

Weightec 348 User Manual - Dutch - 49 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info