Rotisserie burner does not light.Did you push the burner control knob in and hold it in for
20 seconds after the burner ignited?
Try to relight burner by holding burner control knob in
and continue holding in for 20 seconds after burner has
ignited.
Did you wait to see the entire ceramic surface light up
before counting 20 seconds?
When relighting burner by holding burner control knob
in, wait to see the entire ceramic surface become alight
before counting 20 seconds.
Did you repeatedly use the snap ignition until the burner
ignited?
After waiting five minutes for gas to clear, try repeatedly
to use the snap igniter until the burner ignites. Refer to
“ROTISSERIE BURNER IGNITION & USAGE”.
Does the igniter work? Do you see a spark when you
repeatedly use the snap igniter?
Try manually lighting the burner. Refer to “ROTISSERIE
BURNER MANUAL IGNITION”. Call Customer Service.
General Symptoms:
Burner does not light, or Burner has a small flickering
flame.
Some countries have regulators with an excess gas flow
safety device.
The excess flow safety device, which is part of the grill-
to-cylinder connection, may have activated.
To reset the excess flow safety device, turn all burner
control knobs and the cylinder valve to OFF. Disconnect
the regulator from the cylinder. Turn burner control
knobs to START/HI. Wait at least 1 minute. Turn burner
control knobs to OFF. Reconnect the regulator to the
cylinder. Turn cylinder valve on slowly. Refer to “MAIN
BURNER IGNITION”.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
web site. Log onto www.weber.com.
GRILL LIGHT TROUBLESHOOTING
PROBLEMCHECKSOLUTION
Burners burn with a yellow or orange flame, in
conjunction with the smell of gas (This is normal for the
burner lighting tube).
Sear Station
™
burner does not light.
Inspect Spider/Insect screens for possible obstructions.
(Blockage of holes.)
Clean Spider/Insect screens. Refer to “ANNUAL
MAINTENANCE”.
Did you ignite the two adjacent main burners? Refer to
“SEAR STATION
™
IGNITION & USAGE” instructions for
safe lighting procedure.
Verify adjacent main burner ignition by visually
inspecting for a flame.
mWARNING: If ignition does not occur
within five seconds, turn burner control
OFF, wait five minutes to let the gas
clear before you try again.
Does burner light with a match?If you can light Burner with a match, then check the
Crossover
™
Channel on the sear burner. Refer to
“MAINTENANCE” for burner removal and cleaning
procedure.
Does the igniter work? (Do you see a spark when you
repeatedly use the snap igniter?)
Try manually lighting the burner. Refer to “SEAR
STATION
™
IGNITION & USAGE”. Call Customer Service.
General Symptoms:
Burner does not light -or- Burner has a small flickering
flame.
Some countries have regulators with an excess gas flow
safety device.
The excess flow safety device, which is part of the grill-
to-cylinder connection, may have activated.
To reset the excess flow safety device, turn all burner
control knobs and the cylinder valve to OFF. Disconnect
the regulator from the cylinder. Turn burner control
knobs to START/HI. Wait at least one minute. Turn burner
control knobs to OFF. Reconnect the regulator to the
cylinder. Turn cylinder valve on slowly. Refer to “MAIN
BURNER IGNITION”).
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
web site. Log onto www.weber.com.
MAINTENANCE
MAINTENANCE
PROBLEMSSOLUTIONS
Grill light does not turn on.The grill light will activate only when lid is open. Lift the lid to the open position and press the AWAKE button.
Install new batteries. When installing new batteries (alkaline only), confirm that each battery’s plastic wrapping has
been removed. Verify that the batteries are in good condition and have been installed correctly. Refer to “MAINTAINING
THE GRILL LIGHT.”
Grill light turned off and will not turn back on. The light is programmed to turn off automatically after 30 minutes of inactivity. To reactivate the light, make sure lid is
open and press the AWAKE button. Refer to “MAINTAINING THE GRILL LIGHT.”
Grill light does not turn off.The grill light is equipped with a tilt sensor. The tilt sensor turns the light ON when grill lid is opened and OFF when
the grill lid is closed.
NOTE: The AWAKE button will not turn the grill light off. To turn the light off, put the lid in the closed position.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Weber Summit E-670 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Weber Summit E-670 in the language / languages: English as an attachment in your email.
The manual is 5,16 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
