717338
7
Zoom out
Zoom in
Previous page
1/56
Next page
WWW.WEBER.COM
®
7
Timer Timer
1
1 1
2
Timer
1
o:oo
WELL DONE
Timer
1
o:oo
WELL DONE
00:60
0:03+
3X =
11
After initial setup, if the Quick-Read Bars do not appear
and Current Temperature reads “---” after :60, the
Transmitter and Receiver must be paired.
Pairing Instructions:
Press / Hold “1” and “2” on Receiver until you hear Beep
and Current Temperature readout flashes.
Short press “Power” key on transmitter unit within 12
seconds.
Quick-Read Bars and Current Temperature readout
should appear on Receiver within :60, indicating a
successful pairing.
Después de la configuración inicial, si no aparecen las
Barras de lectura rápida y en Temperatura actual se
muestra “---” tras :60 segundos, el Transmisor y el
Receptor deberán emparejarse.
Instrucciones de emparejamiento
Pulse / Mantenga pulsado “1” y “2” en el Receptor hasta
que oiga un pitido y la lectura de Temperatura actual
parpadee.
Pulse brevemente la tecla “Encendido/Apagado” en la
unidad transmisora en 12 segundos.
Las Barras de lectura rápida y la lectura de Temperatura
actual deberían aparecer en el Receptor transcurridos
:60 segundos, indicando que el emparejamiento ha tenido
éxito.
Après la configuration initiale, si les barres de lecture
rapide n’apparaissent pas et que la température actuelle
affiche «---» après :60 secondes, l’émetteur et le
récepteur doivent être jumelés.
Instructions de jumelage:
Appuyez et maintenez enfoncé «1» et «2» sur le
récepteur jusqu’à ce que vous entendiez une tonalité
sonore et que l’affichage de la température actuelle
clignote.
Appuyez brièvement sur le bouton Alimentation de
l’émetteur dans les 12secondes qui suivent.
L’affichage des barres de lecture rapide et de la
température actuelle doit apparaître sur le récepteur
dans les :60 secondes, indiquant la réussite du jumelage.
Wenn nach der Grundkonfiguration die
Schnellanzeigefelder nicht erscheinen und nach “:60” (60
s) als aktuelle Temperatur “---” angezeigt wird, müssen
Sender und Empfänger gekoppelt werden.
Kopplungsanleitung:
“1” und “2” auf dem Empfänger gedrückt halten, bis ein
Piepton ertönt und die aktuelle Temperaturanzeige blinkt.
Drücken Sie innerhalb von 12Sekunden am Sender die Taste
„Power“.
Jetzt sollten innerhalb von “:60” (60 s) die
Schnellanzeigefelder und die Anzeige der aktuellen
Temperatur auf dem Empfänger erscheinen. Die
Kopplung ist damit erfolgreich abgeschlossen.
Alkuasetusten jälkeen, jos pikalukupalkki ei näy ja
nykyinen lämpötila osoittaa arvoa “---” :60 sekunnin
jälkeen, lähetin ja vastaanotin on paritettava.
Paritusohjeet:
Pidä painettuna näppäimiä “1” ja “2” vastaanottimessa,
kunnes kuuluu piippaus, ja nykyisen lämpötilan lukema
vilkkuu.
Paina lyhyesti lähettimen “Power” näppäintä 12 sekunnin
kuluessa.
Pikalukupalkki ja nykyinen lämpötila tulisi näkyä
vastaanottimessa :60 sekunnin kuluessa, jolloin paritus
on onnistunut.
Senderen og mottakeren må pares hvis Quick-Read
Bars (hurtigavlesningslinjene) ikke kommer frem og den
gjeldende temperaturen viser “---” etter :60, etter det
første oppsettet.
Paringsinstruksjoner:
Trykk / hold “1” og “2” på mottakeren helt til du hører et
pip og avlesningen av gjeldende temperatur blinker.
Trykk kort på “Power”-tasten på senderen innen 12
sekunder.
Quick-Read Bars (hurtigavlesningslinjer) og avlesning av
gjeldende temperatur bør vises på mottakeren innen :60,
noe som indikerer vellykket paring.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Weber Style 6741 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Weber Style 6741 in the language / languages: All languages as an attachment in your email.

The manual is 13,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info