807061
3
Zoom out
Zoom in
Previous page
1/8
Next page
Aktobis AG, Borsigstr. 20, D-63110 Rodgau / Germany
www.AKTOBIS.de
Email: Info@Aktobis.de
Features and benefits:
Thermostat for regulating and setting the desired temperature (heating switches off - fan continues to run)
Overheating protection and protection against dripping water
Pure fan operation also possible without heating function
Stepless temperature control (0 ~ 85°C)
Assembly:
Figure 1: Mounting the feet
The housing of the heat gun has two openings (B) on both sides (left and right) for attaching the V-shaped feet (A).
Make sure that the shorter end of the feet is facing backwards. Take two M8 x 40mm screws (D) and slide a
washer (C) onto each. Now insert the screws through the mounting holes of the feet and slide a washer (E) onto
each of the screws. Now screw the feet to the enclosure by fixing the screws in the holes (B). Do this for both
sides.
Figure 2: Mounting the axle and wheels
Take the wheel axle (F) and guide it through the holes at the lower end of the feet so that the axle protrudes
equally on both sides. Secure the position of the axle by inserting a cotter pin (G) through the holes provided on
both sides and fastening it (see picture 2). Now put a washer (H), a wheel (J) and again a washer (H) on each of
the protruding sides of the axle. Now screw a nut (L) to the end of each axle and tighten it well.
Figure 3: Mounting the transport handle
Take the four M5 x 50mm screws (Q) and slide a washer (P) over each one. Place the U-shaped transport handle
(M) on the feet (N) as shown in the picture and align the transport handle so that the two holes in the transport
handle overlap with the two holes in the feet. Now take the four screws and insert two on each side through the
holes to connect the transport handle to the feet. Then slide a washer (P) and a spring washer (T) onto the
protruding ends of the screws. Finally, attach a nut (S) to each end of the bolt and tighten it well so that everything
is firmly and securely connected and mounted.
Now you can put your heat gun into operation !
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WDH BGC30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WDH BGC30 in the language / languages: English as an attachment in your email.

The manual is 0.83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of WDH BGC30

WDH BGC30 User Manual - German - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info