806986
10
Zoom out
Zoom in
Previous page
1/55
Next page
- 9 -
USE
Before using the unit please look at our below installation instruction videos.
This machine adopts a unique energy storage system. It uses the stored cold or heat energy to run the unit for
cooling or heating function. Therefore, please complete cold storage or heat storage in advance before setting
the cooling mode / strong cooling mode or heating mode.
Do not activate the cold storage function in the room that you want to cool. A lot of heat will be blown into
the room during the cold storage function.
For best and fastest result position the unit near an open door or window during storage operation so the hot
air is ventilated out.
No energy storage is needed for dehumidification or ventilation function. You can press the mode button to
choose dehumidification mode or ventilation mode directly without proceeding cold storage or heat storage
in advance.
Notice: After switching on each mode, the fan inside the appliance will be running for 30 seconds first, and
then the appliance will work according to your desired mode function.
1. Connect the power supply
1) For the first use, please connect the power supply and then refer to step 2 of Water inflow.
2) When it is not used for the first time or there is water in the water tank, please insert the power plug
into the power socket and press the power button on the control panel.
2. Water inflow
In case of water shortage alarm (no water in the water tank during the first use or water shortage during
use), please follow the steps below to feed water into the water tank inside the machine.
1) Remove the water inlet knob at the back of the appliance by rotating it anti-clockwisely.
2) Use the water inlet/outlet hose to connect the machine with faucet. Press the water inflow button
and the faucet should be turned on at the same time.
3) When the water level reaches the working level, the water inlet valve will automatically close to
complete the water inlet.
4) Remove the water inlet/outlet hose and screw back the water inlet knob.
3. Cold storage
1) Press the mode button to select the cold storage function.
2) Press the button + or - to set the cold storage temperature. The lower the setting temperature is,
the greater the storage capacity is. Set the temperature range between -9 and 5.
3) After the completion of cold storage, the unit will automatically enter the standby state.
Note:
During cold storage, the wind is at high speed and the swing blade is at the maximum outlet angle. At
this time, the heat energy will be discharged. In a narrow space, please open the doors and windows
for ventilation. Do not activate the cold storage function in the room that you want to cool. A lot of
heat will be blown into the room during the cold storage function. For best and fastest result position
the unit near an open door or window during storage operation so the hot air is ventilated out.
The actual temperature of water in the water tank is displayed during cold storage.
The air inlet and air outlet shall not be covered.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WDH 9000K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WDH 9000K in the language / languages: English, German as an attachment in your email.

The manual is 3.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info