805503
4
Zoom out
Zoom in
Previous page
1/8
Next page
4
FREN
Température de service
Température d’expédition
et de stockage
0°C - +40°C
-10°C à +50°C
Alimentation électrique 230V ac 50Hz
Protection électrique Classe II - IP33
Type de contact
Charge maximale
2 fils (contact libre) - Connecteurs à vis <1.5mm2
Jusqu’à 8A - 250V ac 50Hz
Radiofréquences 868 MHz, <10mW
Normes et homologations
Votre thermostat a été conçu con-
formément aux normes suivantes
ou autres documents normatifs
EN 60730-1:2017 / EN 60730-2-9:2021 / EN IEC 61000-3-2:2019 + AMD1:2021
EN IEC 61000-3-3:2013 + AMD1:2017 + AMD2:2021 / EN 55014-1:2017
EN 55014-2:2015 / EN 55024:2010 + A1:2015 / ETSI EN 301 489-3 V2.1.1
ETSI EN 301 489-1 V2.2.3 / ETSI EN 300 220-1 V3.1.1 / ETSI EN 300 220-2 V3.2.1
EN IEC 63000:2018 / Regulation (EU) 2015/1188 / Regulation (EU) 2013/813
Caractéristiques techniques
Mode de conguration RF
Technical characteristics
Radio conguration mode
1. Installez et branchez le récepteur en respectant les consignes suivantes :
Prêtez une attention particulière au choix de l’emplacement de votre récepteur, en effet quelques précautions sont à prendre
afin de garantir un fonctionnement optimal de votre installation :
- Le récepteur radio fréquence ne devrait pas être placé trop prés de canalisation électrique, hydraulique ou de tout type
d’appareil de communication sans fils (GSM, Wi-Fi…). Une distance d’environ 50cm vous garantira un fonctionnement optimal.
- Veillez à couper l’alimentation électrique avant toute intervention sur les borniers de connexion.
- Brancher votre récepteur au secteur.
2. Ensuite maintenez le bouton poussoir enfoncé pendant 5s, le voyant RF vert doit s’allumer (fixe) indiquant que le récepteur
est désormais en mode de configuration radio en attente de l’adresse de configuration d’un thermostat
3. Référez-vous à la notice du thermostat pour configure le thermostat en mode “RF Init”.
4. Vérifiez que les signaux radio sont correctement reçus par le récepteur. Sur le récepteur, la led verte doit clignoter à chaque
réception d’un signal radio provenant du thermostat.
5. Sortez du mode de configuration Radio du thermostat. (se référer à la notice du thermostat).
6. Votre installation est prête à l’emploi.
1. Install and plug the receiver into the following guidelines:
Pay attention before the installation of your receiver, some routing rules should be make to guaranty an optimal working.
- The receiver must be put at a minimum distance of 50cm of all others electrical or wireless materials like GSM, Wi-Fi router.
- Before wiring work related to the receiver must be carried out only when de-energized.
- Plug your receiver to the power supply.
2. Then press the Receiver push button during 5sec, the Green RF LED should lit up (fixed) indicating that the Receiver is now
in radio configuration mode waiting for a thermostat configuration address.
3. Please refer to the thermostat leaflet for enter the thermostat in “RF Init” mode.
4. Verify that radio signals are correctly received by the Receiver. On the Receiver, the Green LED should blink at each radio
signal received from the thermostat.
5. Exit the Radio configuration mode on the thermostat. (Please refer to the thermostat leaflet).
6. Now starting your installation is ready to works.
Environment (Temperatures)
Operating
Transport and storage
0°C - +40°C
-10°C to +50°C
Power supply 230V ac 50Hz
Electrical protection Class II - IP33
Type of contact
Maximum Load
2 wires (free contact) - Screw connectors <1.5mm2
Up to 8A - 250V ac 50Hz
Radio Frequency 868 MHz, <10mW
Norms and homologations
Your thermostat has been designed
in conformity with the following
standards or other normative
docmuents
EN 60730-1:2017 / EN 60730-2-9:2021 / EN IEC 61000-3-2:2019 + AMD1:2021
EN IEC 61000-3-3:2013 + AMD1:2017 + AMD2:2021 / EN 55014-1:2017
EN 55014-2:2015 / EN 55024:2010 + A1:2015 / ETSI EN 301 489-3 V2.1.1
ETSI EN 301 489-1 V2.2.3 / ETSI EN 300 220-1 V3.1.1 / ETSI EN 300 220-2 V3.2.1
EN IEC 63000:2018 / Regulation (EU) 2015/1188 / Regulation (EU) 2013/813
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Watts WAT BT-RRF FREE CONTACT - Wireless Wall receiver at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Watts WAT BT-RRF FREE CONTACT - Wireless Wall receiver in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1.2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info