805500
5
Zoom out
Zoom in
Previous page
1/15
Next page
PPLIMP2350Bb page 28
GB
5. INSTALLATION AND ELECTRIC CONNECTIONS
5.1. CONTROLLER INSTALLATION
The Heating Controller can be installed directly on a solid base (e.g. a wall). For this purpose the front panel of the
Controller must be removed (fig. 4a) and the back section should be fastened using appropriate screws and pins
(these are not included in the scope of supply) (fig. 4b). Using a knife, remove the protection film before inserting
the upper fastening screw.
If the Controller has been factory fitted with cables for connecting to a pump, valve drive, temperature limiter, sen-
sors etc., take care not to damage or crack the cables during the installation. Furthermore these cables should not
subjected to any tensile stress during installation. The cables will be fixed by means of the device for strain relief at
the heating controller.
If the Heating Controller is delivered together with a hydraulic control unit (for example FRG or FlowBox) and if it is
not attached to that unit by any installation plate or support, it should be installed next to that unit.
Pay attention to the correct connection of the cables if the Controller is not installed directly on a hydraulic control
unit but at some other place for the reason of better access.
Refer to the directions about this in section 5.2 Electric connections.
After making the electric connections, refit the front panel. (fig. 4с).
5.2. ELECTRIC CONNECTIONS
All electric connections must be made by an authorized specialist according to the local regulations on electric
installations. The electrical cables must not come into contact with any hot components.
OK
Fig. 4b
OK
OK
Fig. 4c
Strain relief
Fig. 4a
4a
Flow temperature sensor
Fig. 5
Pump
Outdoor temperature sensor
Voltage
Supply
230 V
L
N
3-point
actuator
blue
white
red
AXM117
brown
Typ 66 / 67
NR230
blue
black
O
COM
C
O
COM
C
O
COM
C
1 brown
2 blue
3 white
ZU
N
L
Optional connection – temperature limitter TB
(option).
The connection is factory fitted with a cable bridge. It must be
removed if connecting TB.
1
2
3
4
> T °C
N
AUF
TB
Close
Common
Open
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Watts Climatic Control H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Watts Climatic Control H in the language / languages: English as an attachment in your email.

The manual is 1.09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info