805581
5
Zoom out
Zoom in
Previous page
1/12
Next page
5
CIVIC1-MOI-IT-W-ML-09-18-Rev.1
Watts Water Technologies, Inc.
EN
Once the correct power is supplied, the control unit carries out
the following phases in sequence:
LED and buzzer tests (about 5 seconds)
Whichever operating mode is selected, the LEDs will switch on
in sequence and the buzzer will sound briefly.
Warm-up of detectors (about 1 minute)
During this phase, which brings the detectors up to the
correct operating temperature, the gas detection system is not
operational. During this phase, if the wiring connections
are correct, the control unit display shows the following:
Operating test (about 3 minutes)
Once the detector warm-up phase is complete, the device
enters the operating test phase. During this phase, all internal
timing is reset to ease operating verification of the detectors
(alarm simulation). In this case, the control unit display shows
the following:
Keep the “Reset/Test” button pressed down for over 1 second
to interrupt the operating test phase. To test the detectors
correctly, proceed as follows:
Gas alarm test
Bring the test cylinder close to the detector grille and release
a small amount of gas (caution: if the gas is aimed directly at
the sensor, this will be permanently damaged). For CO testing
of detectors, smoked produced by combustion can be used.
The control unit will signal the alarm as follows:
Keep the “Reset/Test” button pressed down for 1 second to
silence the alarm (if there is no gas remaining) and terminate
the operating test phase. To restart the Test phase, just keep
the relative button pressed down for about 6 seconds. Repeat
the operations described above to test the other detectors.
Interface Positive
logic
Negative
logic
Power supply LED Green Flashing 1 Hz Flashing 1 Hz
General failure LED Yellow On Off
Detector failure LED (4) Yellow On Off
Alarm and line failure
LED (4) Red On Off
Alarm buzzer No sound No sound
Alarm relay Energised De-energised
Failure relay Energised De-energised
Interface Positive logic Negative logic
Detector
alarm LED Red Off On
Alarm buzzer Continuous sound Continuous sound
Alarm relay De-energised
Energised
(permanently or
pulsed depending
on E2)
Interface Positive
logic
Negative
logic
Detector failure
LED Yellow Off On
Alarm buzzer Intermittent
sound
Intermittent
sound
Failure relay De-energised Energised
General failure LED Yellow On Off
Caution The repeated use or high concentration of interfering
substances (alcohol, lighter fluid etc.) can cause permanen
damage to the sensor and put the device out of order.
Detector failure test
Simulate a failure in the detector as follows:
- disconnect the cable of the detector and verify the following alerts:
- reconnect the detector and press the “Reset/reconnect the
detector and press the “Reset/Test” to return the control unit to
normal operating mode, making the sure the conditions of the
various interfaces are reset.
Normal operation
This is the normal operating phase of the control unit during
which both gas alarm monitoring and self-testing of the
instrument (detector) and the system (control unit) are
active. During this phase, where there are no alarms and/or
abnormalities, the control unit display shows the following:
When dangerous concentrations of gas are detected, the
control unit enters the gas alarm phase and carries out the
following operations:
Once the gas alarm condition is normalised, the control unit
needs to be reset to its normal operating status. Press the
“Reset/Test button on the front of the control unit to reset it.
If there are abnormalities (detector and/or control unit), the con-
trol unit will show the following display:
Interface Positive
logic
Negative
logic
Power supply LED Green Flashing 2 Hz Flashing 2 Hz
General failure LED Yellow On Off
Detector failure LED (4) Yellow On Off
Alarm and line failure
LED (4) Red On Off
Alarm buzzer No sound No sound
Alarm relay Energised De-energised
Failure relay Energised De-energised
Interface Positive
logic
Negative
logic
General failure LED
(for control unit failure) Yellow Off On
Detector failure LED
(for detector failure) Yellow Off On
Alarm buzzer Intermittent
sound
Intermittent
sound
Failure relay De-energised Energised
Interface Positive
logic
Negative
logic
Power supply LED Green On On
General failure LED Yellow On Off
Detector failure LED (4) Yellow On Off
Alarm and line failure
LED (4) Red On Off
Alarm buzzer No sound No sound
Alarm relay Energised De-energised
Failure relay Energised De-energised
Interface Positive logic Negative logic
Detector
alarm LED Red Off On
Alarm buzzer Continuous sound Continuous sound
Alarm relay De-energised
Energised
(permanently or
pulsed depending
on E2)
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Watts CIVIC 4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Watts CIVIC 4 in the language / languages: English, Italian as an attachment in your email.

The manual is 1.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info