Manual Wanders Larix (page 22 of 72) (English, German, Dutch, French)

694510

Zoom out

Zoom in

1/72

• Press button (2) continuously to lower the ames and to switch o the burner (putting the re out: “STAND BY”). Press button

(2) briey to gradually lower the ames.

• Press button (1) to increase the ame height. Briey press button (1) to gradually increase the ames.

• Simultaneously press button (4) and button (2) to turn o the rear burner.

• Simultaneously press button (4) and button (1) to turn on the rear burner again.

• It is not possible to have only the rear burner be lit.

Switching o the appliance

• Press button (2) to lower the ames and to switch o the burner.

• Then press “OFF” button (3) to switch o the entire unit, including the pilot ame.

• If the appliance is not used for a longer period it is advisable that you turn o the gas valve in the gas pipe.

Important: if the pilot ame has gone out for whatever reason, you must wait at least 5 MINUTES before lighting

the pilot ame again.

Gas saving electronics

The electronics in your gas re are programmed to save gas when the appliance is not in use. If the receiver doesn’t receive

a signal from the remote every 3 hours it will switch to the pilot ame. After 5 days it will shut down the gas re completely.

You can prevent this from happening by programming the timer on the remote. By doing this a signal will be send regularly

to the receiver.

Failure

If it looks as if the signals of the remote control are not properly received by the stove (receiver), it may be caused by:

• Empty batteries: change the batteries.

• An electric problem: solve by carrying out a hard reset. To do so, you must disconnect the receiver from its power source by

removing the batteries or disconnecting the adapter. Then press the “RESET” button on the receiver for 8 seconds. Power the

receiver up again and restart the gas re.

• If the appliance often switches o you should contact your installer.

Operation (remote control with EcoWave)

For the complete explanation of the operation via the SYMAX-remote control, please refer to the instruction manual supplied

separately.

Operation (optional Wanders EcoWave app)

It is possible to order the optional Wi-Fi module in order to operate the replace using the Wanders EcoWave app,

The app can be downloaded for free at the Apple App Store and/or the Google Play Store. Incidentally, the app can only be

used in combination with the SYMAX EcoWave remote control.

Control (manual control)

In the event of empty batteries or a defective receiver, the heater can also be operated manually. To do so, the piezo ignition

cable must rst be disconnected from the receiver, before connecting it carefully to the piezo connector (10) on the gas

control unit.

Lighting the re and putting it out

1. Open the gas stopcock which is mounted in the gas pipe leading to the appliance.

2. Press “O I” switch (5) on the gas control block in the “I” position.

3. Turn motor switch (7) on the gas control block all the way to the right. The switch will make a ticking sound.

4. Turn operating switch (6) on the gas control block in the MAN position; an orice (8) becomes visible.

5. Push the metal pin in the orice with something like a small pen. The gas will now ow to the pilot.

6. While keeping the metal pin pressed in, press the (square) ignition fuse (9) (next to the “O I” switch) to ignite the pilot

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Wanders Larix in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6,12 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Wanders Larix Manual

Product: