533430
27
Zoom out
Zoom in
Previous page
1/68
Next page
26
Mounting the suspended model
Illustration 5 Suspension clip
1. Check whether the wall in front of which the hearth is placed is adequately fire-proof. Please read the
section on ‘Fire Safety’, page 21.
2. Check the packaging of the stove and the base. Do not mount the stove or the base when it has been
damaged in the box. If there is any damage, please report to WANDERS.
3. Be careful when unpacking the stove and protect the floor while unpacking: the mouth of the tube
underneath the stove has a sharp edge.
4. Remove the two-piece top plate of the stove (see illustration 1) to avoid any damage.
5. Use the suspension clip (see illustration 5) to as a mould for the holes. Brake of the upper clips and the
edges for the external air. Place the suspension clip on the wall. Never use any synthetic fastenings. Be
sure to place the clip exactly beneath the centre of the outlet and to hold the hooks face upward. The fast-
ening bolts should not protrude more than 10 mm from the wall.
6. If necessary, connect a separate air supply duct (minimum diameter: 150 mm). You can use the connection
at the back or at the bottom. See also illustration 4. Read the next paragraph for placing the external air
supply at the back.
7. Hang the stove in the clips. Mind your back! To decrease the weight you can temporarily remove the glass
pane and the grate. Fasten the top of the stove to the wall.
8. If you opt for a decorative tube please read the section on ‘Assembling the decorative tube’.
9. Mount the flue gas tubes overlappingly.
10. Replace the two-piece top plate on the stove.
11. The model indication can be changed into one in the desired language.
Mounting the rear connection of the external air supply.
1. Follow points 1 to 6 inclusive given in the previous paragraph Mounting the suspending model.
2. Remove the cover plate (A) of the external air supply at the rear of the stove and exchange them. (see
illustration 6)
3. Hang the stove in the clips. (Mind your back!) To decrease the weight you can temporarily remove the
glass pane and the grate. (See also the chapter on ‘Repairs’ on page 27).
4. Put the tube around the tube mouth.
5. Continue with point 9 of the previous paragraph Mounting the suspending model.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wanders Diamant at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wanders Diamant in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wanders Diamant

Wanders Diamant Additional guide - English, German, Dutch, French - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info