Manual Wanders Danta 1400 (page 6 of 36) (English)

571828

Zoom out

Zoom in

1/36

• The Remote Handset has 4 Buttons; these will perform all operations of the re.

• Always leave the dial on the Gas Control Valve set to "ON", the "MAN" position is only for servicing and

emergency use if the handset is misplaced, or the battery fails.

• With each successful button press of the handset, the receiver will emit an audible signal.

• A toggle switch is present on the Gas Control Valve; this should be put into the "O" position if the appliance is

not operated for a long period (over a week).

• The heat output can be manually adjusted by turning the setting knob on the Gas Control Valve.

2.3 Batteries

Remote Handset:

1 x 9V "PP3" Battery, Quality alkaline recommended

Receiver:

4 x 1.5V "AA", Quality alkaline recommended for maximum life.

An alternative AC Mains Adaptor may be used to power the Receiver instead of the 4 AA batteries. Only an AC

Mains Adapter supplied by Wanders may be used. The Mains Adaptor is plugged into the DC 6V socket on the end

of the receiver.

Note - if the AC Mains Adapter is used, remove the 4 AA's from the Receiver, failure to do so could result in damage

and failure of the Receiver. During a period of power outage, the receiver may be unplugged and batteries returned

to the Receiver.

2.4 Replacing the batteries

Handset:

There is a battery level indicator on the display of the handset. When this gets low remove the cover on the rear of

the handset and replace the battery with another 9V PP3 battery.

Receiver:

Three short audible beeps will sound when the appliance is on to indicate that the batteries in the receiver are

getting low.

When the batteries get very low the appliance will be turned o by the remote control. This will fail to happen if

the power supply is interrupted.

To replace the Receiver batteries, slide the cover o of the top of the receiver and use the ribbon to pull the

batteries out. Replace the batteries with new 1.5V AA's, ensuring that the ribbon is located under the batteries and

that the polarity is correct on all 4 batteries.

Never mix new batteries with old; this will result in the new batteries being emptied very quickly.

When the batteries are replaced, it may be necessary to reset the transmitter code, as detailed in the next section.

2.5 Setting the Transmitter code

Press and hold the RESET button with a sharp object (pen or screwdriver) until you hear two audible beeps. After

the second, longer beep, release the RESET button.

Within the next twenty seconds press the down button (Button D g 1.1) on the remote handset until you hear an

additional long signal conrming the code is set.

2.6 To Ignite the appliance

Note - If this appliance is extinguished or goes out in use for any reason, wait 3 minutes before attempting to

relight the appliance. The Gas Control Valve has an interlock device which will not allow relighting until the 3

minutes have passed.

To be able to use the Remote control Handset (g. 1.1), the rocker switch on the Gas Valve, must be turned "ON"

(the "1" position) and the manual Dial set to the "On" position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Wanders Danta 1400 in the language / languages: English as an attachment in your email.

The manual is 3,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wanders Danta 1400

Wanders Danta 1400 User Manual - German - 28 pages

Wanders Danta 1400 Usermanual and installation guide - Dutch - 28 pages

Wanders Danta 1400 User Manual - French - 28 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Wanders Danta 1400 Manual

Product: