571834

Wanders Balsa 100 Manual

24
Zoom out
Zoom in
Previous page
1/64
Next page
24
The Balsa must not be built into the wall, and must be placed on a  oor that is solid enough to hold the
appliance. The distance from the Balsa to the rear wall must be at least 10 cm, and there must be a free space
of at least 80 centimetres to the right and left side of the  replace. Be sure to place the Balsa on a solid  oor
plumb under the  ue pipe.
Insulation
Due to the high temperatures of the exterior walls (up to approximately 150 °C or 300 °F) it is prohibited to
have or to place any combustible materials close to the channel system. The entire concentric pipe system
should be encased with  reproof material from the place where it is out of sight up to the outlet in the exterior
wall. Ventilate the encased concentric pipe system by placing a grate near the  oor and the ceiling on every
oor. Use universal wall clips with a diameter of 150 mm for anchoring the concentric pipe system.
Do not insulate the concentric channel
If an existing chimney is used,  rst make sure whether the chimney is su ciently insulated and is wide
enough to accommodate the concentric pipe system. If the chimney was previously used as a wood-burning
or coal- red stove, it must  rst be professionally cleaned. You must use special WANDERS connecting sets for
connecting a gas hearth to an existing chimney.
Gas connection
• Use a feed pipe with an approved G3/8” stop cock with coupling.
• De-aerate the supply pipe before  tting and fastening the appliance.
• Avoid tension on the operating valve and pipes to avoid gas leakage.
• Check if the connection is gastight.
Placing the concentric channel system
The appliance is approved according to the European CE regulations for gas appliances with the WANDERS
concentric  ue systems (Ø 100 / 150 mm) and are to used only in that combination. The warranty will be partly
or entirely invalid if another system is used during installation. The WANDERS concentric system (Ø 100 / 150
mm) can be used with existing situations or newly built situations.
Instructions for placing the out ow
The out ow of the pipe system can be placed on top of the roof or against the side
wall of the house.
Out ow on top of the roof
When placing the out ow on top of the roof, make sure that there is a distance of at
least 50 cm between the out ow and the edges of the roof, with the exception of a
possible existing ridge. You must also take the place of the out ow into account in
relation to the existing ventilation openings, movable windows and combustion air
supply provisions. Please consult the national and local requirements.
Out ow into the wall
When placing the out ow into the side wall, make sure that there is distance of at least
50 cm between the out ow and the corners of the building, eaves, gutters, balconies
and etceteras. You need not have this distance when the out ow runs to at least the
front side of the overhanging part.
!
Min.
50 cm
Min.
50 cm
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wanders Balsa 100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wanders Balsa 100 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 9,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info