813230
9
Zoom out
Zoom in
Previous page
1/28
Next page
FIRMWARE FWW02 - H09901220
DT2003618_H072267DE0_01 9
- nach der Absetzphase muss das Produkt bei maximaler Leis-
tung laufen, über einen variablen Zeitraum zwischen 6 und 10
Stunden je nach Lackmenge im Körper des Produkts, die ver-
dampfen muss.. Die Funktionszeit bei maximaler Leistung muss
nicht unbedingt kontinuierlich durchgeführt werden. Sie kann
auch in zwei Zeitabschnitte unterteilt werden, mit einer Pause
von mindestens 3-4 Stunden, in der das Produkt ausgeschaltet
ist.
Am Ende dieses Vorgangs ist der Lack eingebrannt und das Pro-
dukt kann mit den geeigneten Einstellungen bei normalem Ge-
brauch verwendet werden.
Wenn nötig, kann ein neuer bei maximaler Leistung laufender Zy-
klus durchgeführt werden, damit jeder Geruchs-Rückstand ent-
fernt wird.
5.2 KONTROLLE DER NETZSPANNUNG UND
FREQUENZ
Bei Einschalten erkennt das Gerät automatisch die Netzspannung
und -frequenz der Stromversorgung.
Wenn Mitteilungen dieser Art erscheinen:
DT2040133_L023 SUP FWS2 12DIGIT_0_P36
50HZ KO
60HZ KO
115V KO
230V KO
DT2040133_L023 SUP FWS2 12DIGIT.xlsx P36 Pag. 36 diI 38
muss ein Fachmann die Geräteeinstellungen ändern.
Nur danach kann das Produkt in Betrieb genommen werden.
5.3 SCHNECKE FÜLLEN
Die Funktion SCHNECKE FÜLLEN ermöglicht das Füllen der Pellets
in der Förderschnecke und ein sofortiges Abladen der Pellets im
Feuerraum, um somit das Einschalten und Zünden des Produkts
zu fördern.
a Bei einem neuen Produkt und wenn die Pellets kom-
plett verbraucht sind, muss die Funktion SCHNECKE
FÜLLEN durchgeführt werden.
Die Funktion SCHNECKE FÜLLEN ist nur möglich, wenn
der Ofen OFF ist.
Zum Ausführen der Funktion SCHNECKE FÜLLEN:
- einige Sekunden F + drücken
- mit - F + die Felder abfahren, bis Sie zur Schrift SCHNE-
CKE FÜLLEN kommen
- mit 3 bestätigen
- die nötige Zeit zum Abschluss des Vorgangs durchführen
6
SCHNECKE GEFUELLT
DT2040133_L023 SUP FWS2 12DIGIT_0_P5
- F +
SCHNECKE FUELLEN
3
IN FUELLUNG
DT2040133_L023 SUP FWS2 12DIGIT.xlsx P5 Pag. 5 diI 50
Anschließend wird das Leeren der Pellets im Brenntopf erfragt.
Siehe Teil "
NACHRICHT TOPF LEEREN
Nur danach kann das Produkt in Betrieb genommen werden.
Meldung "KEINE FUELLUNG"
Zeigt an, dass keine andere Funktion durchgeführt werden kann.
a Die Funktion SCHNECKE FÜLLEN ist nur möglich, wenn
der Ofen OFF ist.
6 DAS PRODUKT STARTEN
Halten Sie einen Moment lang die Taste ON/OFF 4 gedrückt.
Vor dem Eintreten in den normalen Funktionsmodus beginnt der
normale Einschaltmodus, der wie folgt signalisiert wird:
DT2040133_L023 SUP FWS2 12DIGIT_0_P9
20° KONTROLLE
20° START PHASE I
20° START PHASE II
DT2040133_L023 SUP FWS2 12DIGIT.xlsx P9 Pag. 9 diI 38
Wenn der Anlaufzyklus abgeschlossen wurde, stabilisiert sich das
Produkt im normalen Funktionsmodus.
a Wenn während der Startphase (ungef. 12-15 Minuten)
die Verbrennung nicht richtig angelaufen ist, erscheint
eine Sicherheitsmeldung. Siehe Teil "
NACHRICHTEN
SICHERHEITSMELDUNGEN  STÖRUNGEN
”.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wamsler WESTMINSTER PO 81 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wamsler WESTMINSTER PO 81 in the language / languages: German as an attachment in your email.

The manual is 1.64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info