Manual Wamsler Titan (page 27 of 84) (English, German, French, Italian)

813181

Zoom out

Zoom in

1/84

the draught, then a so-called starting fire is to be set first. Towards this end, burn

wood chips/wool in the fireplace or the cleaning hole of the chimney. The fire grate

is to be cleaned before every kindling to ensure the proper inflow of air for burning.

The ashtray is to be emptied regularly (Figure 4). Should the equipment be ex-

tremely hot, use the gloves provided. Please, be careful not to dispose glowing

materials into the waste bin.

Ensure that the ashtray should be fully pushed into the equipment.

Warning! In order to keep the air clean and safeguard the fireplace, do not

exceed the specified maximum fuel quantity, otherwise overheating may oc-

cur, which potentially damage the equipment. Such damage is not covered

with any guarantee. Only a single layer of fuel is allowable to be prepared in

the fireplace. Try to reach lower heating performance only by decreasing the

quantity of fuel, and not by cutting the primary air supply.

1.5 Cleaning and maintenance

After the heating season, it is recommended to clean the fireplace and the flue gas

pipes carefully. Any dropping heating performance is almost always the conse-

quence of the strong contamination of the flues. For cleaning, the baffle plate (Pic-

ture7) is to be pulled forward. This way, the flues can be cleaned from the inside or

– after removing the flue gas pipe – from above. After cleaning, the baffle plate

(Picture 7) is be pushed back fully again.

Warning!

Following every heating season you are advised to examine the fireplace thor-

oughly. If any repair or reconditioning is needed, please, contact your local dealer

in a timely manner, and specify the model number and serial number of your

equipment (as seen on the model plate). External surfaces may be maintained only

after the fireplace cooled down, and following the first commissioning. Use cold

water for cleaning, or soap, washing ingredient in extraordinary cases, then wipe it

dry. Before its first use, clean the ROBAX inspection glass with a wet and clean

cloth, and then put a few drops of glass–ceramics cleaner onto both sides of the

glass, and spread them with the use of kitchen paper tissues. It provides an invisi-

ble film on the valuable surface of the Robax glass. This film helps to keep the

glass clean, and facilitates regular cleaning operations. ROBAX S for slightly con-

taminated surfaces – a commercially available glass surface cleaning agent – may

as well be used for the cleaning of the medium or strongly contaminated glass sur-

faces of the fireplace. Towards this end, spray small quantities of the agent to the

cold surfaces, spread it, and wash it down with a wet cloth, followed by drying with

a clean, soft cloth. In case there are sticky fuel deposits on these surfaces, first

scale simply them with a ceramic-plate scraper held in flat angle, and then clean

the surfaces as described above.

Cleaning of the ceramic surfaces dirt and grease are to be removed with soap

and water.

Cleaning of the soapstone: the soapstone is a natural stone, therefore minor

colour differences may occur; as it is normal, they may not serve as a basis for

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Wamsler Titan in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 1.82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Wamsler Titan Manual

Product: