531880
24
Zoom out
Zoom in
Previous page
1/70
Next page
24
Warning! In order to keep the air clean and safeguard the fireplace, do not
exceed the specified maximum fuel quantity, otherwise overheating may oc-
cur, which potentially damage the equipment. Such damage is not covered
with any guarantee. Only a single layer of fuel is allowable to be prepared in
the fireplace. Try to reach lower heating performance only by decreasing the
quantity of fuel, and not by cutting the primary air supply.
1.5 Cleaning and maintenance
After the heating season, it is recommended to clean the fireplace and the flue gas
pipes carefully. Any dropping heating performance is almost always the conse-
quence of the strong contamination of the flues. For cleaning, the grate (picture 6)
and
furnace chamber walling is to be pulled out (picture 7). This way, the flues can
be cleaned from the inside or – after removing the flue gas pipe – from above. After
cleaning, you must this be pushed back fully again.
Warning!
Following every heating season you are advised to examine the fireplace thor-
oughly. If any repair or reconditioning is needed, please, contact your local dealer in
a timely manner, and specify the model number and serial number of your equip-
ment (as seen on the model plate). External surfaces may be maintained only after
the fireplace cooled down, and following the first commissioning. Use cold water for
cleaning, or soap, washing ingredient in extraordinary cases, then wipe it dry. Before
its first use, clean the ROBAX inspection glass with a wet and clean cloth, and then
put a few drops of glass–ceramics cleaner onto both sides of the glass, and spread
them with the use of kitchen paper tissues. It provides an invisible film on the valu-
able surface of the Robax glass. This film helps to keep the glass clean, and facili-
tates regular cleaning operations. ROBAX S for slightly contaminated surfaces – a
commercially available glass surface cleaning agent – may as well be used for the
cleaning of the medium or strongly contaminated glass surfaces of the fireplace.
Towards this end, spray small quantities of the agent to the cold surfaces, spread it,
and wash it down with a wet cloth, followed by drying with a clean, soft cloth. In case
there are sticky fuel deposits on these surfaces, first scale simply them with a ce-
ramic-plate scraper held in flat angle, and then clean the surfaces as described
above.
Cleaning of the ceramic surfaces dirt and grease are to be removed with soap
and water.
Cleaning of the soapstone: the soapstone is a natural stone, therefore minor col-
our differences may occur; as it is normal, they may not serve as a basis for quality
complaints! To clean the soapstone from dirt and fat with water and soap, as well as
small scratches, use sand paper (grain size 240).
Warning: Under no circumstances you may use sponge, scouring, aggressive
or scratching cleaning agents! If the grate is blocked so that the equipment can-
not serve the intended function, the grate is to be removed for cleaning.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wamsler PRIMO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wamsler PRIMO in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info