Manual Wamsler Linz (page 26 of 84) (English, German, French, Italian)

813203

Zoom out

Zoom in

1/84

onds. In addition, if you intend to put additional fuel into the fire, before the

opening of the door only there may be only ember bed in the burning space, i.e.

no flames may be visible.

Led into the burning space in correspondence with the existing conditions, the secon-

dary air provides for the follow-up burning of the combustible components of in the

burning space. This in fact means smoke and soot-poor burning, which contributes to

the protection of the environment. If you wish to commission the fireplace in a transi-

tional period, please, please first examine the chimney draught, as it can be especially

weak at high external temperatures. Towards this end, hold a burning match in the

slightly opened feeding door. If the flame is not drawn significantly by the draught,

then a so-called starting fire is to be set first. Towards this end, burn wood chips/wool

in the fireplace or the cleaning hole of the chimney. The fire grate is to be cleaned

before every kindling to ensure the proper inflow of air for burning. The ashtray is to

be emptied regularly (picture 5). Should the equipment be extremely hot, use the

gloves provided. Please, be careful not to dispose glowing materials into the waste

bin.

Ensure that the ashtray should be fully pushed into the equipment.

Warning! In order to keep the air clean and safeguard the fireplace, do not ex-

ceed the specified maximum fuel quantity, otherwise overheating may occur,

which potentially damage the equipment. Such damage is not covered with any

guarantee. Only a single layer of fuel is allowable to be prepared in the fireplace.

Try to reach lower heating performance only by decreasing the quantity of fuel,

and not by cutting the primary air supply.

1.5 Cleaning and maintenance

After the heating season, it is recommended to clean the fireplace and the flue gas

pipes carefully. Any dropping heating performance is almost always the consequence

of the strong contamination of the flues. For cleaning, the baffle plate (picture 6 No. 2)

is to be pulled forward. This way, the flues can be cleaned from the inside or – after

removing the flue gas pipe – from above. After cleaning, the baffle plate (picture 6 No.

2) is be pushed back fully again.

Warning!

Following every heating season you are advised to examine the fireplace thoroughly.

If any repair or reconditioning is needed, please, contact your local dealer in a timely

manner, and specify the model number and serial number of your equipment (as seen

on the model plate). External surfaces may be maintained only after the fireplace

cooled down, and following the first commissioning. Use cold water for cleaning, or

soap, washing ingredient in extraordinary cases, then wipe it dry. Before its first use,

clean the ROBAX inspection glass with a wet and clean cloth, and then put a few

drops of glass–ceramics cleaner onto both sides of the glass, and spread them with

the use of kitchen paper tissues. It provides an invisible film on the valuable surface of

the Robax glass. This film helps to keep the glass clean, and facilitates regular clean-

ing operations. ROBAX S for slightly contaminated surfaces – a commercially avail-

able glass surface cleaning agent – may as well be used for the cleaning of the me-

dium or strongly contaminated glass surfaces of the fireplace. Towards this end, spray

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Wamsler Linz in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Wamsler Linz Manual

Product: