Manual Wamsler City (page 25 of 84) (English, German, French, Italian)

813196

Zoom out

Zoom in

1/84

• Before installation pull out the delivery securer off the refractory brick through

the furnace chamber (picture no. 6).

Open the door by raising the handle (Picture 2). If the equipment is hot, you can

use insulated gloves. Adjust the primary air regulator and the fuel switch (Picture 3)

according to the Table 2. Put coal lighter or wood wool onto the fire grate, followed

by wood chips. First insert small pieces of wood, and then larger ones, light them

and close the door again. When the wood burns quickly, and leaves sufficient glow-

ing embers, put additional fuel on the fire. Thereafter, adjust the primary air regula-

tor and the fuel switch according to the Table 2 („Adjustment of the burning air”).

The first kindling should be performed “finely” with little fuel only, so that the parts of

the fireplace are adapted to heat. During the first kindling, the generation of smell is

normal and absolutely undangerous.

1.3 Putting out of operation

• Let the glowing ember burn to ashes and the fire-place get cold.

• Empty the furnace chamber and the ash bin.

• Close the doors and push the primary air regulator totally to the left.

1.4 Heating instructions

The fireplace should be operated only with closed furnace chamber door. Fire-

places belonging to type 1 have self-locking furnace chamber doors. These doors

may be opened only for kindling, loading or when cleaning the furnace chamber

(otherwise draught problems may occur with other equipment connected to the

same chimney).

Warning!

When opening the furnace chamber door, any incorrect handling or insuffi-

cient draught may induce smoke. Always ensure that the furnace chamber

door may be opened only slowly, first just to a small extent, and then fully

after a few seconds. In addition, if you intend to put additional fuel into the

fire, before the opening of the door only there may be only ember bed in the

burning space, i.e. no flames may be visible.

Led into the burning space in correspondence with the existing conditions, the sec-

ondary air provides for the follow-up burning of the combustible components of in

the burning space. This in fact means smoke and soot-poor burning, which contrib-

utes to the protection of the environment. If you wish to commission the fireplace in

a transitional period, please, please first examine the chimney draught, as it can be

especially weak at high external temperatures. Towards this end, hold a burning

match in the slightly opened feeding door. If the flame is not drawn significantly by

the draught, then a so-called starting fire is to be set first. Towards this end, burn

wood chips/wool in the fireplace or the cleaning hole of the chimney. The fire grate

is to be cleaned before every kindling to ensure the proper inflow of air for burning.

The ashtray is to be emptied regularly (Figure 4). Should the equipment be ex-

tremely hot, use the gloves provided. Please, be careful not to dispose glowing

materials into the waste bin.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Wamsler City in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 1.62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Wamsler City Manual

Product: