802048
14
Zoom out
Zoom in
Previous page
1/20
Next page
14
EN
Electrical Wiring
L2L1
Mounting the Charger
Hot wires
Black + Red
Ground
Green or
Bare wire
INSTALLATION
Hardwired Installation
x2
ø3.5 x 9.5mm
1. Carefully remove your charger from the
packaging box and hang it from the top of the
wallplate.
1. For bottom wiring installation, feed the power
supply wires through the bottom port with enough
length to easily connect the wires to the terminals.
2. Replace the two wallplate screws to secure
your charger to the wallplate. Do not over-tighten
2. Connect the electrical wires according to the
diagram on the left.
3. Use copper conductors only within the wire
size range of 10 to 6 AWG (6mm2 to 16mm2)
4. Strip 1/2 (12mm) of insulation o each wire,
insert the wires per the diagram, and tighten each
connector screw to 11.5in·lbs (1.3N·m)
For rear wiring installation, feed the power supply
wires through the rear port (and through the rubber
grommet, if not using conduit) with enough length
to easily connect the wires to the terminals
NOTE: If using a conduit connection, pull the
wiring through before connecting the conduit
Ensure the electrical panel supports a 208/240V
dedicated circuit with a new, dedicated two-pole
circuit breaker, rated for the selected amperage
(see following section). The voltage between the
hot wires (L1 and L2) must be 208/240V.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wallbox Pulsar Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wallbox Pulsar Plus in the language / languages: English as an attachment in your email.

The manual is 1.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wallbox Pulsar Plus

Wallbox Pulsar Plus Installation Guide - English - 29 pages

Wallbox Pulsar Plus Quick start guide - English - 8 pages

Wallbox Pulsar Plus User Manual - English - 34 pages

Wallbox Pulsar Plus User Manual - German - 30 pages

Wallbox Pulsar Plus User Manual - Dutch - 34 pages

Wallbox Pulsar Plus Installation Guide - French - 29 pages

Wallbox Pulsar Plus User Manual - French - 34 pages

Wallbox Pulsar Plus User Manual - Swedish - 31 pages

Wallbox Pulsar Plus Installation Guide - Spanish - 29 pages

Wallbox Pulsar Plus Installation Guide - All languages - 17 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info