517983
43
Zoom out
Zoom in
Previous page
1/122
Next page
GB
43
7.0 INSTALLING THE VACUUM SERVO UNIT (SEE
C 1)
The vacuum servo unit (B 2) regulates the throttle-setting and controls the
speed of the vehicle. The kit contains a vacuum servo unit with a flexible
throttle lever. The best places for installation in the engine compartment
are the bulkheads and the inside wheel arches. In order to avoid damage
to the electronics and mechanics, make sure that temperatures does not
exceeded 100°C. C 2 to E 3 illustrate various methods for attaching the
wire to the carburettor. D 2 gives a detailed list of the components for
the vacuum servo unit. The following points describes how the wire is to
be attached to the carburettor. To ensure perfect functioning of the cruise
control, the throttle control-lever must be in good condition (e.g. not slack,
not seized, etc.). If your vehicle has fuel injection, the installation
instructions refer to the throttle control-lever and not to the carburettor,
and in the case of diesel engines to the fuel injection pump.
1. Decide which method is possible for attaching the throttle lever to the
throttle linkage (see C 2 and C 3). At vehicles without throttle lever
the attachment can be made directly at the accelerator (see E 2)
Note: The servo has about 40 mm of travelling distance. Choose a
stopping point at the accelerator or cable of the vehicle, which
corresponds as nearly as possible to the distance of 40 mm. Non-
compliance with this would result in excessive strain of the servo or a
restricted working range. The wire must pull on the throttle control
lever in a straight line. The sideways pull must not be more than 20°.
2. Using two 6 x 19 mm metal screws , attach the vacuum servo-unit to
the inside wheel arch or the bulkhead of the vehicle.
3. Depending on the method for attaching the actuator cable the
illustrated components will be used (see D 1 and D 2)
CAUTION! The throttle lever must be kept away from rotating
or hot surface parts.
202
5.0 NØDVENDIG VERKTØY (SE
A 5 TIL A 17)
Følgende verktøy er nødvendig for installasjon og montering:
- Målestokk (se A 5)
- Kjørner (se A 6)
- Hammer (se A 7)
- Metallborsett (se A 8)
- Boremaskin eller drill (se A 9)
- Vanlige skrutrekkere og stjernetrekkere i forskjellige størrelser
(se A 10)
- Flatfil og halvrundfil
- Blyant eller filtpenn
- Fastnøkkelsett (se A 11)
- Skrallenøkkelsett (se A 12)
- Jekk og bilbukker (se A 13)
Til elektrisk tilkobling og testing trenger du:
- diodetestlampe (se A 1) eller voltmeter (se A 2)
- krympetang (se A 15)
- evt. isoleringsbånd
- kabelbånd
- varmekrympeslange
- Varmluftsføner
- loddebolt (se A 16)
- loddetinn (se A 17)
Book_MS-50_A6.p65 10-02-2003, 11:1143
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Waeco MagicSpeed MS50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Waeco MagicSpeed MS50 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info