596626

Wacom DTU-1031 Manual

42
Zoom out
Zoom in
Previous page
1/62
Next page
42
IndexContents
42
IndexContents
Interactive pen display
The pen tip does not function. Make sure you are using the pen that originally came with your
interactive pen display. Other pens may not function properly on the
pen display.
Check the Control Panel’s P
EN tab and verify that a CLICK function is
assigned to the pen tip.
Make sure the status LED lights blue when the tip is pressed. If the LED
does not light, verify that the USB cable is plugged into an active port
on your computer. If you are using only one USB connector to connect
the pen display with your computer, plug in the other connector if you
have an additional USB port available on your computer.
If the LED still does not light, you may have defective hardware (see
troubleshooting
).
The pen tip and screen cursor
do not properly line up.
Open the Wacom Control Panel and select the C
ALIBRATE tab. Continue
with calibrating and adjusting the pen display
.
Changing the function settings
for the pen has no effect.
Make sure you change the settings for the pen and application that you
are using. See application-specific settings
.
The pen side switch does not
work.
Be sure you are using the pen that originally came with your pen
display. Other pens may not function properly on the pen display.
Be sure to press the switch when the pen tip is within 5 mm
(0.2 inch) of the pen display active area. Do this without pressing down
on the pen tip.
In the Wacom Control Panel, verify that the switch is set to the proper
function you are expecting to occur for the application and tool you are
using.
Check the S
IDE SWITCH MODE. If CLICK & TAP is selected, you will need
to first press the switch, then touch the pen tip to the pen display
screen surface in order to perform a click function.
Make sure the status LED lights blue when you press the switch.
If not, verify that the USB cable is plugged into an active USB port on
your computer; the LED will not light if the USB cable is not plugged
into an active port.
If the LED does not light, you may have defective hardware (see
troubleshooting
).
The screen cursor moves but
it does not jump to the pen tip
location when the pen is
placed on the display screen,
and it does not follow the pen
tip when the pen is moved
across the display.
Make sure the Wacom driver has loaded properly by opening the
Wacom Control Panel. If the driver did not load you will see an error
message. If an error message appears, reboot your computer.
If the problem persists, refer to the installation
instructions and reinstall
the Wacom driver software. (For Macintosh, you must restart your
computer after installing the Wacom driver for proper operation.)
If you have customized the switch on your pen to toggle between pen
mode and mouse mode, make sure that your pen display is operating
in pen mode.
… 42 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wacom DTU-1031 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wacom DTU-1031 in the language / languages: English as an attachment in your email.

The manual is 2,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info