779591

VTech VM343 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
Set alert tone
Low battery tone
You can set the parent unit to beep when the
parent unit operates in low battery condition.
Press MENU when the parent unit is not in
use.
Press or to choose ALERT TONE, then
press SELECT.
Press or choose Low Battery Tone,
then press SELECT.
Press or to choose On or Off, then press
SELECT to confirm your selection.
No link alert
You can set the parent unit to beeps when the
link between the parent unit and the baby unit is
lost.
Press MENU when the parent unit is not in
use.
Press or to choose ALERT TONE, then
press SELECT.
Press or to choose No Link Alert, then
press SELECT.
Press or to choose On or Off, then press
SELECT to confirm your selection.
Sound alert
You can turn the sound alert feature on so that,
whilst in SPLIT-VIEW mode, the parent unit
beeps whenever the baby unit detects sounds.
Press MENU when the parent unit is not in
use.
Press or to choose ALERT TONE, then
press SELECT to select.
Press or to choose Sound Alert, then
press SELECT.
Press or to choose On or Off, then press
SELECT to confirm your selection.
1.
2.
3.
4.
1.
2.
3.
4.
1.
2.
3.
4.
Monitor the temperature
To monitor the temperature of your baby’s room,
you can turn the parent unit temperature alert
feature on. It beeps whenever the temperature
detected by the baby unit falls out of the desired
temperature range.
Minimum temperature
You can set the desired minimum room
temperature of the room temperature alert
range. The minimum temperature can be set
between 11 oC (52 oF) and 20 oC (69 oF).
Press MENU when the parent unit is not in
use.
Press or to choose TEMPERATURE,
then press SELECT.
Press or to choose Minimum, then
press SELECT.
Press or to choose the desired
temperature, then press SELECT to confirm
your selection.
Maximum temperature
You can set the desired maximum room
temperature of the temperature alert range. The
maximum temperature can be set between
21 oC (70 oF) and 30 oC (86 oF).
Press MENU when the parent unit is not in
use.
Press or to choose TEMPERATURE,
then press SELECT.
Press or to choose Maximum, then
press SELECT.
Press or to choose the desired
temperature, then press SELECT to confirm
your selection.
1.
2.
3.
4.
1.
2.
3.
4.
Temperature alert
You can set the parent unit to beep when the
temperature is out of the preset temperature
range.
Press MENU when the parent unit is not in
use.
Press or to choose TEMPERATURE,
then press SELECT.
Press or to choose Alert, then press
SELECT.
Press or to choose On or Off, then press
SELECT to confirm your selection.
Temperature format
You can choose to display the temperature in
Celcius (oC) or Fahrenheit (oF).
Press MENU when the parent unit is not in
use.
Press or to choose TEMPERATURE,
then press SELECT.
Press or to choose Format, then press
SELECT.
Press or to choose Fahrenheit or
Celsius, then press SELECT to confirm your
selection.
1.
2.
3.
4.
1.
2.
3.
4.
Vibration
You can turn the vibration feature on so that the
parent unit vibrates when
the link between the parent unit and the baby
unit is lost;
the temperature detected by the baby unit
falls out of the preset temperature range.
Press MENU when the parent unit is not in
use.
Press or to choose VIBRATION, then
press SELECT.
Press or to choose On if speaker is off,
Always on or Off.
On if speaker is off - The parent unit
vibrates only when the speaker of the
parent unit is turned off.
Always on - The parent unit vibrates
regardless of the speaker volume setting.
Off - The parent unit will not vibrate at all.
Press SELECT to confirm your selection.
Play lullaby
There are 5 lullabies to choose from. The
selected lullaby plays repeatedly.
To play lullaby:
Press to play lullaby
To stop lullaby:
Press again to stop playing lullaby.
To skip to the next lullaby:
Press to skip to the next lullaby.
NOTE
Lullaby playback is paused when the parent unit is
talking to the baby unit. Lullaby playback resumes
when the parent unit finishes using the TALK feature.
•
•
1.
2.
3.
•
•
•
4.
Rename the baby unit
You can rename the baby unit. Once the baby
unit is renamed, its new name will appear in the
sub-menu of below options:
Sensitivity
Temperature
Rename
Pair/unpair
Press MENU when the parent unit is not in
use.
Press or to choose RENAME, then
press SELECT.
Press SELECT to select the baby unit.
Press or to choose the desired name for
the baby unit, then press SELECT to confirm
your selection.
Night vision
The baby unit has infrared LEDs that allow
you to see your baby clearly at night or in a
dark room. When the baby unit detects low
light levels, the infrared LEDs are switched on
automatically.
NOTE
When the infrared LEDs are on, the image is in
black and white. This is normal due to external light
sources.
TIP
Depending on the surroundings and other
interfering factors, like lightings, objects, colours and
backgrounds, the display resolution may vary. Adjust
the baby unit’s angle or place the baby unit at a higher
level to prevent glare and blurry display.
•
•
•
•
1.
2.
3.
4.
General product care
To keep this product working well and looking good,
follow these guidelines:
Avoid putting it near heating appliances and devices
that generate electrical noise (for example, motors
or fluorescent lamps).
DO NOT expose it to direct sunlight or moisture.
Avoid dropping the product or treating it roughly.
Clean with a soft cloth.
DO NOT immerse the parent unit and the baby unit
in water and do not clean them under the tap.
DO NOT use cleaning spray or liquid cleaners.
Make sure the baby unit and parent unit are dry
before you connect them to the mains again.
Storage
When you are not going to use the baby monitor for
some time, remove the rechargeable battery from the
parent unit. Store the parent unit, the baby unit and the
adaptors in a cool and dry place.
•
•
•
•
•
•
If you have difficulty with your baby monitor, please try
the suggestions below.
Why does the
baby monitor
not respond
normally?
Try the following:
1. Disconnect the power to the
baby unit and the parent unit.
2. Remove the battery in the parent
unit. Then install the battery
again.
3. Wait a few minutes before
connecting power back to the
baby unit and the parent unit.
4. Turn the baby unit on and theon and theand the
parent unit.
5. Wait for the parent unit to
synchronise with the baby unit.
Allow up to one minute for this to
take place.
Why don’t
the power-on
light of the
baby unit and
parent unit
go on when I
switch on the
units?
The rechargeable battery of the
parent unit could be empty and
the parent unit is not connected
to the mains. Insert the appliance
plug into the parent unit and put
the adaptor in a wall socket. Then
press to switch on the parent unit
and to establish connection with the
baby unit.
The baby unit may not be
connected to the mains. Connect
the baby unit to the mains. Then set
ON/OFF switch to ON to switch the
baby unit on and to establish
connection with the parent unit.
Why doesn’t
my parent unit
charge while
connected to
AC power?
You may have used the battery for
a long time. Replace a new battery.
Why is my
screen in
black and
white?
The screen is in black and white
during the nighttime or in a dark
room. This is normal due to external
light sources.
Why do I get
glare or blurry
display on my
screen when
viewing my
baby at night?
During nighttime or in a dark
room, the surroundings and other
interfering factors, like lightings,
objects, colours and backgrounds
may affect the image quality on
your parent unit screen. Adjust the
baby unit’s angle or place the baby
unit at a higher level to prevent
glare and blurry display.
Why does the
baby monitor
produce a
high-pitched
noise?
The units may be too close to each
other. Make sure the parent unit
and the baby unit are at least
1 metre / 3 feet away from each
other.
The ON/OFF
light on the
baby unit
flashes and
the parent unit
displays .
The baby unit isn’t paired with the
parent unit.
Make sure both parent unit and
baby unit are on before pairing.
Press MENU when the parent
unit is not in use.
Press or to choose
PAIR/UNPAIR CAM, then press
SELECT.
Press or to choose Pair
CAM, then press SELECT.
Press or to choose an
empty baby unit slot, then
press SELECT. The parent unit
screen displays Press and hold
the pair button at the CAM
for 5 seconds until the power
indicator flashes..
Immediately press and hold
PAIR on the bottom of the baby
unit. The LED light flashes
quickly.
When pairing is successful, the
screen displays the view of the
newly paired baby unit. The LED
light on the new baby unit remains
on.
If pairing fails, the screen
displays Pairing failed. Try the
pairing process again.
1.
2.
3.
4.
5.
•
Why does the
parent unit
beep?
The baby unit may be out of range.
Move the parent unit closer to the
baby unit (but not less than
1 metre / 3 feet).
If the parent unit is powered by the
provided battery, it may not have
enough charge for the parent unit to
perform normally. Charge the
battery in the parent unit for up to
12 hours.
The temperature of your baby’s
room may be too high or too low.
Why does
the parent
unit react too
quickly to
other sounds?
The baby unit also picks up other
sounds than those of your baby.
Adjust the sensitivity level to a
lower level or adjust the speaker
volume on the parent unit.
Why don’t I
hear a sound/
Why can’t I
hear my baby
cry?
The parent unit speaker volume
may be too low or off. Press VOL+
to increase the volume.
You may have set a low sound
sensitivity level. See Adjust the
sound sensitivity of the baby
unit to change the setting.
Why can’t I
establish a
connection?
Why is the
connection
lost every now
and then?
Why are
there sound
interruptions?
The baby unit may be out of range.
Move the parent unit closer to the
baby unit (but not less than
1 metre / 3 feet).
Other electronic products may
cause interference with your baby
monitor. Try installing your baby
monitor as far away from these
electronic devices as possible.
Important safety
instructions
When using your equipment, basic safety precautions
should always be followed to reduce the risk of fire,
electric shock and injury, including the following:
Follow all warnings and instructions marked on the
product.
Adult setup is required.
This product is intended as an aid. It is not
a substitute for responsible and proper adult
supervision and should not be used as such.
This product is not intended for use as a medical
monitor.
Do not use this product near water. For example,
do not use it next to a bath tub, wash bowl, kitchen
sink, laundry tub or swimming pool, or in a wet
basement or shower.
CAUTION: Use only the batteries indicated in
this manual. There may be a risk of explosion if a
wrong type of battery is used for the parent unit.
Use only the supplied rechargeable battery.
Use only the adaptors included with this product.
Incorrect adaptor polarity or voltage can seriously
damage the product.
Baby unit power adaptor: Input 100-240V AC
50/60 Hz; output: 6V DC 1000mA
Parent unit power adaptor: Input 100-120V AC
50/60 Hz; output: 5V DC 1000mA.
For pluggable equipment, the socket-outlet shall
be installed near the equipment and shall be easily
accessible.
The power adaptors are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place
if it is plugged into a ceiling, under-the-table or
cabinet outlet.
1.
2.
3.
4.
5.
6.
7.
8.
Unplug this product from the wall outlet before
cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
Unplug the power cords before replacing batteries.
Do not cut off the power adaptors to replace them
with other plugs, as this causes a hazardous
situation.
Do not allow anything to rest on the power cords.
Do not install this product where the cords may be
walked on or crimped.
This product should be operated only from the type
of power source indicated on the marking label. If
you are not sure of the type of power supply in your
home, consult your dealer or local power company.
Do not overload wall outlets or use an extension
cord.
Do not place this product on an unstable table,
shelf, stand or other unstable surfaces.
This product should not be placed in any area
where proper ventilation is not provided. Slots and
openings in the back or bottom of this product
are provided for ventilation. To protect them from
overheating, these openings must not be blocked
by placing the product on a soft surface such as
a bed, sofa or rug. This product should never be
placed near or over a radiator or heat register.
Never push objects of any kind into this product
through the slots because they may touch
dangerous voltage points or create a short circuit.
Never spill liquid of any kind on the product.
To reduce the risk of electric shock, do not
disassemble this product, but take it to an
authorised service facility. Opening or removing
parts of the product other than specified access
doors may expose you to dangerous voltages
or other risks. Incorrect reassembling can cause
electric shock when the product is subsequently
used.
You should test the sound reception every
time you turn the units on or move one of the
components.
Periodically examine all components for damage.
Be aware of possible loss of privacy whilst using
public airwaves. Conversations may be picked
up by other nursery monitors, cordless phones,
scanners, etc.
Children should be supervised to ensure that they
do not play with the product.
The product is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
Cautions
Use and store the product at a temperature
between 0oC and 40oC.
Do not expose the product to extreme cold, heat
or direct sunlight. Do not put the product close to a
heating source.
Batteries should not be exposed to excessive heat
such as bright sunshine or fire.
Make sure the baby unit and the adaptor cord(s)
are always out of reach of the baby, at least 3 feet
away from the baby or cot, to avoid a possible
strangulation hazard.
Never place the baby unit inside the baby’s cot or
playpen. Never cover the baby unit or parent unit
with anything such as a towel or a blanket.
Other electronic products may cause
interference with your baby monitor. Try
installing your baby monitor as far away
from these electronic devices as possible:
wireless routers, radios, mobile telephones,
intercoms, room monitors, televisions, personal
computers, kitchen appliances and cordless
telephones.
1.
2.
3.
4.
5.
6.
Customer service and
product warranty
IMPORTANT
Please retain this booklet with your sales receipt as
proof of the date of purchase.
Customer Service
Please call our Consumer Services Department on
01235 546810 (from UK) or +44 1235 546810
(outside UK) and a service representative will be
happy to help you.
Technical specications
Frequency
control
Crystal controlled PLL synthesizer
Transmit
frequency
Baby unit: 2406 - 2475 MHz
Parent unit: 2406 -2475 MHz
Channels 24
LCD 4.3” Colour LCD
(WQVGA 480x272 pixel)
Nominal
effective range
Maximum power allowed by FCC
and IC. Actual operating range may
vary according to environmental
conditions at the time of use.
Power
requirements
Use only power adaptor listed below:
Baby unit:
Ten Pao International Ltd.
Model : S006MV0600100, Input
100-240V AC 50/60Hz 300mA,
Output 6VDC 1000mA (EU plug).
Model : S006MB0600100, Input
100-240V AC 50/60Hz 300mA,
Output 6VDC 1000mA (UK plug).
Parent unit:
Ten Pao International Ltd.
Model : S006MV0500100, Input
100-240V AC 50/60Hz 300mA,
Output 5VDC 1000mA (EU plug).
Model : S006MB0500100, Input
100-240V AC 50/60Hz 300mA,
Output 5VDC 1000mA (UK plug).
Use only the rechargeable battery
listed below:
BYD Lithium Battery Company
Limited
Model: BT198555/BT298555, 3.7V,
950mAh, Lithium Polymer
CAUTION: Risk of explosion if
battery is replaced by incorrect type
disposed of used batteries according
to the instruction.
Disposal of batteries and
product
The crossed-out wheelie bin symbols
on products and batteries, or on their
respective packaging, indicates they
must not be disposed of in domestic
waste as they contain substances that
can be damaging to the environment
and human health.
The chemical symbols Hg, Cd or Pb,
where marked, indicate that the battery
contains more than the specified value
of mercury (Hg), cadmium (Cd) or
lead (Pn) set out in Battery Directive
(2006/66/EC).
The solid bar indicates that the product
was placed on the market after 13th
August, 2005.
Help protect the environment by
disposing of your product or batteries
responsibly.
For more information, please visit:
www.recycle-more.co.uk
www.recyclenow.com.
Frequently asked questions
VTech Telecommunications Ltd.
A member of THE VTECH GROUP OF COMPANIES.
Distributed in the U.K. by VTech Electronics Europe plc.,
VTech is the registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
© 2015 for VTech Telecommunications Ltd.
All rights reserved. 05/15. VM343_UK_CIB_V1.0
Designed to fit your home.
And your life.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for VTech VM343 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of VTech VM343 in the language / languages: English as an attachment in your email.

The manual is 3.31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info