819201
6
Zoom out
Zoom in
Previous page
1/68
Next page
6
EN
WWW.VONROC.COM
3. ASSEMBLY
Before any work on the power tool, remove
the battery.
The battery must be charged before first
use.
Inserting the battery into the machine (Fig. D)
Ensure that the exterior of the battery is
clean and dry before connecting to the
charger or machine.
1. Insert the battery (8) into the base of the ma-
chine as shown in Fig. D.
2. Push the battery forward until t clicks into place.
Removing the battery from the machine (Fig. D)
1. Push the battery unlock button (10)
2. Pull the battery out of the machine as shown in
Fig. D.
Checking the battery charging status (Fig. E)
To check the battery charge status, push the
button (11) on the battery shortly.
The battery has 3 LED lights indicating the
charge level.
When none of the indicators light up the battery
is empty and must be charged immediately.
Charging the battery with the charger (Fig. E)
1. Remove the battery (8) from the machine.
2. Turn the battery (8) to upside down position and
slide it onto the charger (9) as shown in Fig. E.
3. Make sure that the battery (8) is fully inserted
into the slot.
4. Plug the charger into an electrical outlet. After
a short while the LED indicators on the charger
(13) will light up to show the charger status.
The charger has 2 LED indicators (13) which indi-
cate the status of the charging process
Red LED Status Green LED status Charger status
Off Off No power
Off On
Standby mode:
- No battery is
inserted or,
- Battery inserted
but charging has
finished
On Off Battery charging in
progress
Fully charging a 2Ah battery may take up to 60
minutes.
Fully charging a 4Ah battery may take up to 120
minutes.
After the battery is fully charged remove the charger
plug from the outlet and remove the battery from the
charger.
When the machine is not being used over a
longer period of time it is best to store the
battery in charged condition.
4. OPERATION
On/Off switch (Fig. B)
To turn on the work light, select the desired op-
erating mode (I / II) using the On/Off switch (7).
To switch the work light off, select ‘0’ using the
On/Off switch (7).
Operating
mode Power Luminous
flux
Runtime
(2Ah battery)
Runtime
(4Ah battery)
I 10W 900lm 4 hours 8 hours
II 20W 1800lm 2 hours 4 hours
Adjusting the lamp body (Fig. C)
The position of the lamp body (2) may be adjusted
over a 300° range by swiveling up and down.
1. Release the locking knobs (4) on both sides of
the lamp body (2)
2. Adjust the lamp body (2) to the desired position
3. Secure the lamp body (2) in place by tightening
the locking knobs (4) on both sides.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc WL503DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc WL503DC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 11.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info