764062

Vonroc WC502AC Manual

10
Zoom out
Zoom in
Previous page
1/64
Next page
10
EN
WWW.VONROC.COM
of the machine.
- Only use diamond cutting discs that are
suitable for dry cutting.
- Always replace both cutting discs at the
same time.
- Never attempt to remove the guard.
• Place the machine on a stable surface.
• Loosen the Allen screws (12) using the Allen
key (13).
• Loosen the locking knob (3) and lower the base
(7).
• Remove the guard (6).
• Keep the spindle lock button (5) pressed to lock
the spindle (14).
• Loosen the outer flange (15) using the flange
key (16). To untighten, turn clockwise. To tighten,
turn anti-clockwise.
• Remove the old cutting disc (17), the spacers
(18), the old cutting disc (19), the spindle
sleeve (20), and the inner flange (21).
• If necessary, clean the flanges (15 & 21).
• Mount the inner flange (21), the spindle sleeve
(20), the new cutting disc (19), the spacers
(18), and the new cutting disc (17).
• Firmly tighten the outer flange (15) using the
flange key (16).
• Release the spindle lock button (5).
• Mount the guard (6).
• Raise the base (7) and tighten the locking knob
(3).
• Firmly tighten the Allen screws (12) using the
Allen key (13).
4. OPERATION
Setting the slot width (fig. B - E)
The slot width can be set using the spacers be-
tween the cutting discs. The number of spacers
between the cutting discs determine the slot width.
- Do not set the slot width during use.
- Always mount at least one spacer
between the cutting discs.
• Determine the slot width.
• Mount the spacers (18) around the cutting
discs (17 & 19) in the required order. Refer to
the chapter “Replacing the cutting discs”.
Setting the slot depth (fig. A & F)
The slot depth is variable between 5 and 40 mm.
The slot depth can be read from the scale (4).
Do not set the slot depth during use.
• Slacken the locking knob (3).
• Tilt the base (7) to the required position. Set
a slot depth approximately 3 mm deeper than
the required depth to compensate for possible
unevenness of the wall surface.
• Tighten the locking knob (3).
Switching on and off (fig. A)
• To switch on the machine, keep the lock-off but-
ton (2) pressed and simultaneously press the
on/off switch (1).
• To switch off the machine, release the on/off
switch (1).
Using the laser (fig. A)
• To switch on the laser (23), press the on/off
switch (24).
• To switch off the laser (23), release the on/off
switch (24).
Overload protection
The machine is equipped with an overload protec-
tion device which automatically switches off the
machine if the machine is overloaded.
• Switch off the machine.
• Remove the machine from the workpiece.
• Switch on the machine.
• Run the machine at no-load for approximately
1 minute to allow the machine to cool down.
Dust extraction (fig. G)
Only use the machine when it is connected to a
vacuum device which is approved for stone dust.
The vacuum device must be suitable for the material
to be worked. Use a special vacuum device when
working with toxic materials or where toxic dust is
produced.
- Never use a household vacuum cleaner.
The use of a household vacuum cleaner
can easily damage both your health
and the vacuum cleaner.
- Always use the dust extraction adapter.
- Make sure that the hose of the vacuum
device is securely connected to the
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc WC502AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc WC502AC in the language / languages: English, German, Dutch, French, Italian, Polish, Turkish, Spanish as an attachment in your email.

The manual is 5,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info