778596

Vonroc TM502XX Manual

6
Zoom out
Zoom in
Previous page
1/36
Next page
6
EN
WWW.VONROC.COM
You must use the center of the stud to avoid
cracking or splitting the timber during
installation.
2. Mark a minimum of four mounting holes over
the stud centers using the wall plate as a guide.
Position two holes at either end of the wall plate
(1). Use the provided spirit level (4) to ensure
the wall plate (1) is level.
3. Pre-drill the holes to a minimum depth of 55mm
using a 4.5mm drill bit. If installing in hard-
wood, a slightly larger diameter and deeper
hole may be required.
4. Place the washers (W-C) onto the lag bolts (W-
A). Attach the wall plate (1) to the wall using the
lag bolts (W-A).
Option B: Installing in masonry (Figure E)
Ensure there is a minimum of 35mm of
actual concrete/brick thickness in the
location of each hole.
Drill into solid concrete/bricks only. Do not
drill into mortar joints.
1. Mark a minimum of four mounting holes using
the wall plate (1) as a guide. Position two holes
at either end of the wall plate (1). Use the provi-
ded spirit level (4) to ensure the wall plate (1) is
level.
2. Drill the holes to a minimum depth of 60mm
using a 10mm masonry drill bit. Clean out the
holes after drilling.
3. Fully insert a concrete anchor (W-B) into each
hole. Tap the anchor in using a hammer if requi-
red.
4. Place the washers (W-C) onto the lag bolts (W-
A). Attach the wall plate (1) to the wall using the
lag bolts (W-A).
Attach Mounting Arms to TV (Figure F)
1. Using a second person for assistance, lay your
TV face down on something soft so as not to
scratch the TV screen. Check the back of your
TV to find the appropriate mounting pattern.
Do not place the TV face down onto a table
smaller than the TV itself, as doing so may
crack or damage the TV screen.
2. Sort through the provided bolts (M-A, M-B, M-C)
until you find the correct size that fits into the
mounting holes on the back of your TV. Test if
the bolts can be tightened by hand for at least
three full turns. Do not yet fully tighten the
bolts.
If you feel resistance while turning the bolt
you must stop immediately and select a
shorter bolt. Forcing in an oversized bolt
may cause damage to your TV (see figure G)
3. Remove the bolts from the TV once you have
selected the correct bolt size.
Refer to your local hardware supplier for the
correct bolts and washers if none of the
supplied bolts will fit your TV.
4. Gently place the mounting arms (2) on the back
of the TV. If the back of your TV is curved or re-
cessed you may need to use one or more of the
supplied spacers (M-E or M-F). When using a
spacer you may also need to use a longer bolt.
Keep in mind that the bolt must always be able
to turn at least three full turns (see figure G).
5. Place the washers (M-D) onto the previously
selected bolts. Attach the mounting arms (2) to
the TV using the bolts. Do not over tighten the
bolts, as doing so may cause damage to your
TV.
Attach TV to wall (Figure H)
1. Using a second person for assistance, carefully
lift the TV and hook the arms (2) over the top of
the wall plate (1). Note that there are two height
options on the mounting arms (2) to choose
from.
2. Gently pull down on the unlocking cords (3) on
the mounting arms (2) to open the locks into
the ready position.
3. Slowly lower the bottom of the TV until the
bottom of the mounting arm (2) locks into the
bottom of the wall plate (1). Release the unloc-
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc TM502XX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc TM502XX in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 4.93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info