764112

Vonroc SG502DC Manual

78
Zoom out
Zoom in
Previous page
1/104
Next page
78
DA
WWW.VONROC.COM
• Det kan tage op til 60 minutter at lade 2 Ah
batteriet helt op.
• Det kan tage op til 120 minutter at lade 4 Ah
batteriet helt op. Når batteriet er ladet helt op,
skal du tage opladerens stik ud af kontakten og
fjerne batteriet fra opladeren.
Når maskinen ikke bruges gennem en
længere periode, er det bedst at opbevare
batteriet i opladet tilstand.
Tilslutning af motorenheden til sprøjteenheden
(fig. D)
• Med den ene hånd skal du holde motorenheden
(8) lige op, og med den anden hånd skal du
placere sprøjteenheden (7) i en 90˚ vinkel på
motorenheden (8). Som vist på figur D.
• Juster sprøjteenhedens (7) åbning med hakket i
motorenheden (8). Roter sprøjteenheden (7) 90
grader ned, indtil du hører et klik.
Frakobling af motorenheden og sprøjteenheden
(fig. E.)
• Hold motorenheden (8) og tryk frakoblingslåsen
(6) i retning mod sprøjteenheden (7), og drej
den 90˚ grader for at fjerne sprøjteenheden (7).
Tilslutning og frakobling af beholderen til sprøj-
teenheden.
• For at tilslutte: Få beholderen (11) til at flugte
med beholderhætten (10) og stram.
• For at frakoble: Løsn beholderen (11) fra behol-
derhætten (10)
Udskiftning af mundstykket og mundstykkenålen
Mundstykket vil være monteret på sprøjtepistolen,
når den tages ud af æsken. Følg disse trin for at
udskifte mundstykket.
• Løsn mundstykkemøtrikken (17) og fjern den.
• Tag mundstykkehovedet (15) og mundstykket
(14) ud af maskinen.
• Løsn mundstykkenålen (13) ved hjælp af
nålenøglen (18) som vist på figur I.
• Tag den nye mundstykkenål (24 eller 26) og
placer den i sprøjteenheden igen, og stram den
ved hjælp af mundstykkenøglen (18)
• Tag det nye mundstykke (25 eller 27) og fastgør
det til mundstykkehovedet (15)
• Placer mundstykkehovedet (15) og mundstyk-
kesamlingen i sprøjteenheden igen
• Luk det ved at stramme mundstykkemøtrikken
(17).
4. DRIFT
Preparing the spray gun for use
Step 1: Viscosity/diluting of the paint
This appliance can process spray materials up to
max. 70 DIN/sec (viscosity). Low-viscosity coa-
ting substances, water- and solvent based paints,
finishes, primers, 2 component paint, clear finishes,
staining sealers and wood sealer preservatives often
do not need diluting. High-viscosity Wall paints, thick
varnishes and thick stains often do need diluting.
Tip! With low-viscocity use the smaller nozzle and
with high-viscocity use the bigger nozzle.
Warning! Always use wall paint that is
smooth and without any granules or lumps.
Otherwise the nozzle will become clogged.
PAINT PREPARATION
Check/test the viscosity of the to be sprayed
material.
• Put the stirring rod (12) in the container(11)
which includes the to be sprayed material and
pull it out and see how the material drips. When
it looks like liquid chocolate, this material is
ok for testing at step 4 (Test and adjusted the
spray jet effect, spray volume and spray flow).
When the spraying material is very thick and gel-li-
ke, dilute it by 5 or 10%.
For small batches this can easily done by using the
special stirring rod:
1. Put the stirring rod (12) in the container like
shown in figure E1 and add spray material up to
one of the lines. Like shown in figure E2.
2. For 10%: Add the suitable thinning solvent up to
the next line. For 5%: Add the suitable thinning
solvent up to half of the next line.
3. Stir the thinning solvent through the spray
material until it is completely mixed.
Check viscosity again, when it looks like liquid cho-
colate, this material is ok for testing at step 4 (Test
and adjusted the spray jet effect, spray volume and
spray flow). Still to thick? Repeat the process by
adding an additional 5 or 10% thinning solvent.
Tip! Most wall paints are thick and may need up to
40% dilution.
… 78 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc SG502DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc SG502DC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 10,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info