778551

Vonroc S3_SG503DC Manual

8
Zoom out
Zoom in
Previous page
1/84
Next page
8
EN
WWW.VONROC.COM
7. Reload lever
8. LED work light switch
9. Safety tip
10. Belt hook
11. Adjustment knob
12. Battery LED indicators button
13. Battery LED indicators
14. Charger
15. Charger LED indicators
3. ASSEMBLY
Before any work on the power tool, remove
the battery.
The battery must be charged before first
use.
Inserting the battery into the machine (Fig. B)
Ensure that the exterior of the battery is
clean and dry before connecting it to the
charger or machine.
1. Insert the battery (2) into the base of the
machine as shown in Fig. B.
2. Push the battery forward until it clicks into place.
Removing the battery from the machine (Fig. B)
1. Push the battery unlock button (3).
2. Pull the battery out of the machine like shown
in Fig. B.
Checking the battery charging status (Fig. C)
• To check the battery charge status, push the
button (12) on battery shortly.
• The battery has 3 lights indicating the charge
level, the more lights that burn, the more
charge the battery has left.
• When the lights are not burning it means
the battery is empty and must be charged
immediately.
Charging the battery with the charger (Fig. C)
1. Take the battery (2) from the machine.
2. Turn the battery (2) to upside down position and
slide it onto the charger (14) as shown in Fig. C.
3. Push the battery until it is fully pushed into the
slot.
4.
Plug the charger plug into an electrical outlet and
wait for a while. The LED indicators on the charger
(15) will lighten up and show the charger status.
The charger has 2 LED indicators (15) which
indicate the status of the charging process:
Red LED
Status
Green LED
status Charger status
Off Off No power
Off On
Standby mode:
- No battery is inserted or,
- Battery inserted but charging
has finished
On Off Battery charging in progress
• Fully charging the 2Ah battery may take up to
60 minutes.
• Fully charging the 4Ah battery may take up to
120 minutes.
After the battery is fully charged remove the charger
plug from the outlet and remove the battery from
the charger.
When the machine is not being used over a
longer period of time it is best to store the
battery in charged condition.
Application (Fig. D)
For this tool, use one of the following length for
staples or nails:
• Staples: Type 55: 15-25mm
• Nails: Type 47: 15, 20, 25, 30 or 32mm
Loading the nails or staples (Fig. D-G)
• Choose the correct nail or staple for the job.
• Place the tacker (1) on its side with the battery
(2) pointing to the right, like show in fig. E.
• Open de cartridge shaft (6) by slightly pressing
the reload lever (7).
• Pull the reload lever (7) to the right to open the
cartridge shaft (6).
For nails:
• Place the nails at the top of the cartridge shaft
(6). Like shown on the label of the cartridge
shaft, see example fig. F.
For staples:
•
Place the staples at the bottom of the cartridge
shaft (6). Like shown on the label of the cartridge
shaft, see example fig. G.
• Slide the cartridge shaft (6) back until it clicks.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc S3_SG503DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc S3_SG503DC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 8.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info