Manual Vonroc S3-SG502DC (page 79 of 104) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish)

764115

Zoom out

Zoom in

1/104

WWW.VONROC.COM

Step 2: Preparing the spray surface

• Cover the area around the to be sprayed area

thoroughly and over a wide area. Any surface

that is not covered properly can unintentionally

be sprayed.

Warning! Be aware of your surroundings

when spraying outside, wind can cause

unintentional spraying of your not covered

surroundings.

• The spray surface needs to be clean, dry, and

free from grease or dust.

• Polished surfaces should be lightly sanded, and

the sanding dust removed.

Step 3: Filling the paint container

• Remove the container (11) from the Spray unit.

• Fill the container with to be sprayed material to

a maximum of 800ml.

• Adjust the riser pipe (23) according to the

position you are going to use the spray gun in.

Spraying angle up like show in Fig. F. spraying

angle down like show in Fig. G

• Make sure the gasket and riser pipe (23) are

properly installed in the container cap (10).

Tighten the container (11) onto the container

cap (10).

Step 4: Test and adjust the spray jet effect, spray

volume and spray ﬂow. (Fig. A + B)

Note: Before starting to spray the work surface, it

is advisable to make an initial test by spraying a

small area on scrap material.

Tip! With low-viscocity use the smaller nozzle and

with high-viscocity use the bigger nozzle.

1. Choose the jet effect: Horizontally

•

or verti-

cally

•

. By turning the nozzle adjusting ring (16)

left or right.

2. Adjust the spray volume with Spray volume

adjusting wheel (9) by turning it to the left – to

reduce the volume, to the right + to increase.

Note: Low volume is advised for smaller object

or surfaces. High volume is advised or bigger

surfaces.

Tip: We recommend starting at the minimum

setting.

3. Adjust the spray ﬂow by using the spray ﬂow

adjustment knob(2): turn the knob to the left

to reduce the ﬂow, to the right to increase the

ﬂow. Note: The thinner the paint the lower the

ﬂow should be, when using thicker paint make

sure to use a higher ﬂow.

Tip: Several light layers rather than one thick layer

will help prevent the paint running.

4. Aim the spray gun to the to be sprayed surface

and pull the trigger (1). Hold the front of the

spray gun around 20-30 cm away from the to

be sprayed surface. Make long arm movements

rather than short wrist movements like show in

ﬁgure H. The most suitable method of surface

spraying is with a cross-pattern, starting with

horizontal passes and ﬁnishing with light verti-

cal passes. See ﬁgure J.

5. Release the trigger (1) to stop the spraying.

Check Spray Pattern Quality A good spray pat-

tern is evenly distributed as it hits the surface, if

not (add highest spray ﬂow) check the following:

- Spray tip may be worn.

- A smaller spray tip may be needed.

- Material may need to be thinned.

7. Adjust the Jet effect (step A), spray volume

(step B) and Spray ﬂow (step C) depending on

the paint, object- surface to be sprayed and

desired coverage. Repeat steps D to H when not

satisﬁed with the test results.

Always let the paint/varnish/stains dry according to

the recommend dry time of the spray material for

applying multiple coats. Several light coats rather

than one thick coat will help prevent the paint

running.

5. VEDLIGEHOLDELSE

Før rengøring og vedligeholdelse skal du

altid slukke for maskinen og trække

netstikket ud af kontakten.

Rengøring efter hver brug

Det er vigtigt, at sprøjtepistolen rengøres grundigt

efter hver brug. Hvis den ikke rengøres, vil det

næsten helt sikkert resultere i blokeringer, og den

fungerer muligvis ikke næste gang. Garantien dæk-

ker ikke en sprøjtepistol, der ikke er blevet rengjort

korrekt af brugeren.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc S3-SG502DC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 10,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vonroc S3-SG502DC Manual

Product: