Manual Vonroc S2-AG501DC (page 8 of 72) (English, German, Dutch, French, Italian, Turkish, Spanish)

764085

Zoom out

Zoom in

1/72

WWW.VONROC.COM

e) Do not use a battery pack or tool that is dama-

ged or modiﬁed. Damaged or modiﬁed batteries

may exhibit unpredictable behaviour resulting in

ﬁre, explosion or risk of injury.

Do not expose a battery pack or tool to ﬁre

or excessive temperature. Exposure to ﬁre or

temperature above 130 °C may cause explosion.

NOTE The temperature „130 °C“ can be replaced

by the temperature „265 °F“.

Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range speciﬁed in the instructions.

Charging improperly or at temperatures outside

the speciﬁed range may damage the battery and

increase the risk of ﬁre.

6) Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replacement

parts. This will ensure that the safety of the

power tool is maintained.

Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

SAFETY WARNINGS COMMON FOR GRINDING

OR ABRASIVE CUTTINGOFF OPERATIONS

a) This power tool is intended to function as a

grinder tool. Read all safety warnings, instructi-

ons, illustrations and speciﬁcations provided

with this power tool. Failure to follow all

instructions listed below may result in electric

shock, ﬁre and/or serious injury.

b) Operations such as sanding, wire brushing,

polishing are not recommended to be perfor-

med with this power tool. Operations for which

the power tool was not designed may create a

hazard and cause personal injury.

c) Do not use accessories which are not speciﬁ-

cally designed and recommended by the tool

manufacturer. Just because the accessory

can be attached to your power tool, it does not

assure safe operation.

d) The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and ﬂy apart.

e) The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories

cannot be adequately guarded or controlled.

f) Threaded mounting of accessories must match

the grinder spindle thread. For accessories

mounted by ﬂanges, the arbour hole of the acces-

sory must ﬁt the locating diameter of the ﬂange.

Accessories that do not match the mounting hard-

ware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for loose

or cracked wires. If power tool or accessory is

dropped, inspect for damage or install an unda-

maged accessory. After inspecting and installing

an accessory, position yourself and bystanders

away from the plane of the rotating accessory

and run the power tool at maximum no-load

speed for one minute. Damaged accessories will

normally break apart during this test time.

Wear personal protective equipment. Depending

on application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece

fragments. The eye protection must be capable

of stopping ﬂying debris generated by various

operations. The dust mask or respirator must be

capable of ﬁltrating particles generated by your

operation. Prolonged exposure to high intensity

noise may cause hearing loss.

i) Keep bystanders a safe distance away from

work area. Anyone entering the work area must

wear personal protective equipment. Frag-

ments of workpiece or of a broken accessory

may ﬂy away and cause injury beyond immedia-

te area of operation.

j) Hold the power tool by insulated gripping surfa-

ces only, when performing an operation where

the cutting accessory may contact hidden

wiring or its own cord.Cutting accessory con-

tacting a “live” wire may make exposed metal

parts of the power tool “live” and could give the

operator an electric shock.

k) Position the cord clear of the spinning acces-

sory. If you lose control, the cord may be cut or

snagged and your hand or arm may be pulled

into the spinning accessory.

l) Never lay the power tool down until the acces-

sory has come to a complete stop. The spinning

accessory may grab the surface and pull the

power tool out of your control.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc S2-AG501DC in the language / languages: English, German, Dutch, French, Italian, Turkish, Spanish as an attachment in your email.

The manual is 7,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vonroc S2-AG501DC Manual

Product: