764060

Vonroc S-WC501AC Manual

7
Zoom out
Zoom in
Previous page
1/52
Next page
EN
7
WWW.VONROC.COM
6) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the
power tool is maintained.
b)
Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
ADDITIONAL SAFETY WARNINGS
FOR
WALL CHASER
• Do not work materials containing asbestos.
Asbestos is considered carcinogenic.
• Wear safety goggles, hearing protection and
if necessary other protective means, such as
safety gloves, safety shoes, etc.
• Before use, remove all nails and other metal
objects from the wall.
• Be aware of hidden pipes and wiring when
cutting slots into walls.
• Always hold the machine with two hands.
• Do not use the machine without the guard.
• Inspect the cutting discs before each use.
Do not use cutting discs which are bent, crac-
ked, or otherwise damaged.
• Make sure that the cutting discs are properly
mounted.
• Make sure that the cutting discs rotate in the
correct direction.
• Do not use the machine with the cutting discs
facing upwards or to the side.
• Only use cutting discs that are suitable for use
with the machine.
•
Only use cutting discs with the correct dimensions.
• Do not use other accessories than cutting discs.
• Do not use the machine when a maximum slot
depth is required that exceeds the maximum
slot depth of the cutting discs.
• Make sure that your hands do not touch the
rotating parts.
• Always work in the correct working direction
(see indication on the base).
• Let the machine run at no load in a safe area
after mounting the cutting discs. If the machine
vibrates strongly, immediately switch off the
machine, remove the mains plug from the
mains, and try to solve the problem.
•
Beware that the cutting discs continue to rotate
for a short period after switching off the machine.
Do not attempt to bring the cutting discs to a
standstill yourself.
• Never put the machine down on a table or a
workbench before it has been switched off.
Kickback
Kickback is the upward and backward movement of
the cutting discs when the cutting discs unexpec-
tedly touch an object. Securely hold the machine
with both hands during use. Keep your attention
focused on the operation.
Kickback is usually caused by:
- unintentionally touching hard objects or materi-
als with the rotating cutting discs;
- blunt cutting discs;
- cutting discs that are not properly mounted;
- cutting into a previous cut;
- a lack of attention to the operation;
- an instable stance.
Electrical safety
Always check that the voltage of the power
supply corresponds to the voltage on the
rating plate.
• Do not use the machine if the mains cable or
the mains plug is damaged.
•
Only use extension cables that are suitable for
the power rating of the machine with a minimum
thickness of 1.5 mm
2
. If you use an extension
cable reel, always fully unroll the cable.
2. MACHINE INFORMATION
Intended use
Your wall chaser has been designed for making
slots in masonry. The machine is only suitable for
right-hand use.
TECHNICAL SPECIFICATIONS
Model No.
WC501AC, S_WC501AC,
S2_WC501AC
Mains voltage 230V~
Mains frequency 50Hz
Power input 1700W
No-load speed 4000 min
-1
Slot width 14/19/29mm
Slot depth 5-40mm
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc S-WC501AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc S-WC501AC in the language / languages: English, German, Dutch, French, Italian, Turkish, Spanish as an attachment in your email.

The manual is 4,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info