Manual Vonroc S-RS501DC (page 10 of 36) (English, German, Dutch, French)

764103

Zoom out

Zoom in

1/36

WWW.VONROC.COM

•

To stop the machine, release the on/off switch (2).

Adjusting the base plate (Fig. B)

Due to its movability, the baseplate (7) angle

adapts to the workpiece. Furthermore, the length

of the baseplate can be adjusted depending on the

required sawing depth.

1. Loosen the baseplate bolts (11) using the hex

key (10) provided.

2. Adjust the baseplate (7).

3. Tighten the baseplate bolts (11) using the hex

key (10) provided. It is possible to store the hex

key onto the machine, as shown on Fig. B.

Plunge cutting (Fig. D)

Plunge cutting may only be used on soft materials

such as wood, aerated concrete, gypsum plaster

boards, etc. However, this requires a certain practi-

se and is only possible with short saw blades.

Place the saw onto the workpiece and switch it on.

2. Ensure that the bottom edge of the footplate

rests on the workpiece surface as shown.

3. Slowly saw into the workpiece at an angle, mo-

ving the saw to a vertical position and continue

to saw along the cutting line.

4. Switch the saw off and lift off the workpiece

when the work is complete.

Flush cutting (Fig. E)

Elastic bi-metal saw blades allow you to saw

protruding objects (e,g, water pipes, iron bars, etc,)

nearby the wall.

1. Apply the saw blade directly to the wall and

bend slightly so that the footplate rests against

the wall. Pay attention that the saw blade

always extends beyond the diameter of the

material being worked.

Switch the machine on and saw off the workpiece

keeping constant lateral pressure against the wall.

Optimum use

• Adjust saw blade and stroke rate to suit the ma-

terial to be processed. For right radius curves it

is best to use a narrow saw blade. Apply coolant

or lubricant to deal with the ﬂuttering produced

along the cut line when sawing metal.

• Check wood, chip boards, building materials

etc, for hard materials (nails, screws etc.), befo-

re sawing and remove them, if necessary.

•

Clamp material well. Do not support the workpie-

ce with hand or foot. Do not touch objects or the

ﬂoor with the saw running (danger of backlash).

• Put the footplate on the surface of the workpie-

ce, and saw through it with constant contact

pressure or feed. If the saw blade seizes switch

the machine off immediately. Spread the gap

with a suitable tool and pull out the saw blade.

• After ﬁnishing work, switch off the machine and

only put down after it has come to a complete

standstill.

5. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and remove the

battery pack from the machine.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that the

ventilation openings are free of dust and dirt. Re-

move very persistent dirt using a soft cloth moiste-

ned with soapsuds. Do not use any solvents such

as gasoline, alcohol, ammonia, etc. Chemicals such

as these will damage the synthetic components.

ENVIRONMENT

Faulty and/or discarded electrical or

electronic apparatus have to be collected at

the appropriate recycling locations.

Only for EC countries

Do not dispose of power tools into domestic waste.

According to the European Guideline 2012/19/EC

for Waste Electrical and Electronic Equipment and its

implementation into national right, power tools that

are no longer usable must be collected separately

and disposed of in an environmentally friendly way.

WARRANTY

VONROC products are developed to the highest

quality standards and are guaranteed free of defects

in both materials and workmanship for the period

lawfully stipulated starting from the date of original

purchase. Should the product develop any failure

during this period due to defective material and/or

workmanship then contact VONROC directly.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc S-RS501DC in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,94 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vonroc S-RS501DC Manual

Product: