764168

Vonroc S-GT501DC Manual

11
Zoom out
Zoom in
Previous page
1/64
Next page
EN
11
WWW.VONROC.COM
4. Plug the charger plug into an electrical outlet
and wait for a while. The LED indicators on the
charger (5) will lighten up and show the charger
status.
The charger has 2 LED indicators (5) which indicate
the status of the charging process:
Red LED Status Green LED status Charger status
Off Off No power
Off On
Standby mode:
- No battery is
inserted or,
- Battery inserted
but charging has
finished
On Off Battery charging in
progress
• Fully charging the 2Ah battery may take up to
60 minutes.
• Fully charging the 4Ah battery may take up to
120 minutes.
After the battery is fully charged remove the charger
plug from the outlet and remove the battery from
the charger.
When the machine is not being used over a
longer period of time it is best to store the
battery in charged condition.
Mounting the Protection guard (Fig. B1)
• Fit the protection guard (10) onto the trimmer
head housing.
• Secure the guard using the screw (11) delivered.
Mounting the guardrail (Fig. B2)
• Squeeze the ends of the guardrail (12) together
and slide into the holes of the trimmer head
housing
• The guardrail can be set in different protection
distances. To adjust the rail, simply press or pull
the rail.
Mounting the front handle (Fig. D1)
• Place the handle (8) on the holder mounted on
the upper shaft.
• Fit the bolt in the hexagon hole and mount the
knob (9) onto the bolt.
Adjusting the front handle (Fig. D2)
• Unscrew the knob (9) slightly and press or pull
the front handle (8) in to desirable position. This
can either be down or upwards and rotatable
around upper shaft.
When using the machine sideways always
use the sidewheel.
Mounting of the side wheel (Fig. E)
• Slide side wheel (13) over the side wheel holder
(14).
Mounting the wire spool (Fig. F1)
Before replacing the spool clean the
machine from any dirt.
• Place the spring (17) into the spool housing
(18). Make sure the wider side of the spring is
placed on the trimmer head.
• Place the spool reel (16) over the spring (17).
Make sure the wires are passed through the
holes inside the housing (18). (Fig. F2)
• Cover the spool reel with the spool cover (15)
and fasten it by turning the cover tightly.
Replacing the spool (Fig. F1)
• Remove the spool cover (15).
• Take out the spool reel (16) but leave the spring
(17) inside.
• Take the new spool reel (GT801AA) and place
it over the spring (17). Make sure the wires are
passed through the holes inside the housing
(18). (Fig. F2)
• Cover the new spool reel with the spool cover
(15) and fasten it by turning the cover tightly.
4. OPERATION
Using the tap and go system (Fig. G)
• When the wire is too short, switch the machine
on and press the tip of the spool reel (19) on
the ground (make sure this is done on a hard
surface).
• This will release the wire in order to get longer.
• The wire will be cut on the correct length auto-
matically by the blade mounted in the protecti-
on guard (10).
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc S-GT501DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc S-GT501DC in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 7,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info