Manual Vonroc RT501AC (page 14 of 76) (English, German, Dutch, French, Italian, Polish, Spanish)

764058

Zoom out

Zoom in

1/76

WWW.VONROC.COM

Bench Mounting

The work bench should be very stable to

eliminate vibration when the router is

operating.

Each table leg has an opening at the bottom for

securing the assembled table to a suitable work

bench. The work bench should be level and strong

enough to support the weight of the table and the

router. Use appropriate fasteners and bolts to secu-

re the router table to the work bench.

Plug in the Router (Fig. A)

Ensure the router table power cord is not

connected into the power outlet.

For safety reasons, your electric router may

only be connected to the mains through the

router table’s safety switch unit.

1. Press the red OFF button to ensure the router

table is switched OFF (0).

2. Ensure the router switch is in the OFF (0) position.

3. Plug the router power cord into the outlet on the

switch box. Secure the router power cord so that

it does not interfere with the operation of the

router.

4. Plug the router table power cord into a power

outlet.

Depth of Cut

The depth of cut affects the rate and quality of

cut. The plunge lock lever on the router holds the

router at the desired height and depth of cut. Refer

to instruction manual that came supplied with your

router for details on how to adjust the depth of cut.

Turning On the Router

Once the router is properly mounted to the router

table, you will be able to operate the router using

the router table switch box.

1. Switch the router to the ON (I) position.

NOTE: The router table is primarily intended for

use with a router ﬁtted with a ‘lock-on’ switch.

If your router does not have this feature it will

be necessary to ﬁx its switch in place using

a clamping device. Ensure to remove this

clamping device as soon as you use the router

without the router table.

2. To start the router press the GREEN ON (I) but-

ton on the router table.

3. To stop router press RED OFF button on the

router table.

Using the router table

Check that the guard is in good working

condition every time you use the machine

and regularly clean the dust and chip guard.

NOTE: If you are using a large diameter routing bit

that removes a large amount of material from the

workpiece it may be necessary to make several

passes, increasing the amount of material removed

each time, in order to prevent overloading your

electric router. If this is the case, adjust the fence

assembly so that a reduced router bit radius is

exposed to the workpiece and make the required

amount of cuts before setting the cutting width as

described below for the ﬁnal pass.

1. Fit a router bit to the electric router.

2. Adjust the cutting depth, cutting width, feather

boards and fence assembly as described on the

previous pages.

3. Switch the router on using the safety switch

unit and allow it to reach its full speed.

4. Use a push stick to feed the workpiece slowly

and evenly through the rotating router bit.

5. Switch the router table off and allow the bit to

come to a complete stop before you remove the

workpiece from the table top.

Feed direction (Fig. U)

Do not guide the router in the direction of

rotation of the router bit to avoid the danger

of losing control of the router.

Feed the workpiece from right to left. The material

must be fed against the cutting edge of the router

bit, ensure that the workpiece is tight against the

fence.

Fitting and removing router bits

The router can unintentionally start and

cause injury. Disconnect the router table

and your electric router from the mains

before proceeding.

1. Place the router table on its side.

2. From the underside of the worktable ﬁt or

remove a router bit to your router as described

in the router’s operating instructions.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc RT501AC in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 9,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vonroc RT501AC Manual

Product: