764105

Vonroc RS502AC Manual

7
Zoom out
Zoom in
Previous page
1/28
Next page
EN
7
WWW.VONROC.COM
DESCRIPTION
The numbers in the text refer to the diagrams on
page 2-3.
1. Handle
2. Lock-on button
3. On/Off button
4. Handle unlock button
5. Auxiliary handle
6. Baseplate
7. Saw blade
8. Chuck
9. Clamping lever
10. Baseplate bolts
3. ASSEMBLY
Before carrying out any work on the
machine, disconnect the mains plug from
the power supply.
Replacing the saw blade (Fig. A, C)
When mounting the saw blade, wear
protective gloves. Danger of injury when
touching the saw blade.
Only use saw blades that correspond with
the characteristic data given in the
operating instructions.
Mounting the saw blade
Make sure the blade holder is free of material
debris (such as splinters of wood or metal).
1. Turn the clamping lever (9) as far to the left as
possible and hold it in this position.
2. Insert the saw blade in the chuck (8). Check
that the saw blade is securely fixed and that the
teeth are pointing downwards.
3. Let go of the clamping lever. Check whether the
saw blade is locked in place.
Make sure to use the right sawblade for the corres-
ponding material. Included with the machine is a
coarse sawblade for wood and a fine sawblade for
metal and plastics.
Removing the saw blade
1. Turn the clamping lever (9) as far to the left as
possible and hold it in this position.
2. Remove the saw blade from the chuck (8).
3. Let go of the clamping lever.
4. OPERATION
Switching on and off (Fig. A)
• To switch on the machine, press the on/off
switch (3).
• To switch the machine to continuous mode,
keep the on/off switch (3) pressed and simulta-
neously press the lock-on button (2).
• To switch off continuous mode, press the on/off
switch (3) again.
• To switch off the machine, release the on/off
switch (3).
Adjusting the base plate (Fig. B)
Due to its movability, the baseplate (6) angle
adapts to the workpiece. Furthermore, the length
of the baseplate can be adjusted depending on the
required sawing depth.
1. Loosen the baseplate bolts (10) using the hex
key provided.
2. Adjust the baseplate (6).
3. Tighten the baseplate bolts (10) using the hex
key provided.
Plunge cutting (Fig. D)
Plunge cutting may only be used on soft materials
such as wood, aerated concrete, gypsum plaster
boards, etc. However, this requires a certain practi-
se and is only possible with short saw blades.
1.
Place the saw onto the workpiece and switch it on.
2. Ensure that the bottom edge of the footplate
rests on the workpiece surface as shown.
3. Slowly saw into the workpiece at an angle, mo-
ving the saw to a vertical position and continue
to saw along the cutting line.
4. Switch the saw off and lift off the workpiece
when the work is complete.
Flush cutting (Fig. E)
Elastic bi-metal saw blades allow you to saw
protruding objects (e,g, water pipes, iron bars, etc,)
nearby the wall.
1. Apply the saw blade directly to the wall and
bend slightly so that the footplate rests against
the wall. Pay attention that the saw blade
always extends beyond the diameter of the
material being worked.
2.
Switch the machine on and saw off the workpiece
keeping constant lateral pressure against the wall.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc RS502AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc RS502AC in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info