Manual Vonroc RS501DC (page 7 of 28) (English, German, Dutch, French)

764104

Zoom out

Zoom in

1/28

WWW.VONROC.COM

10. Hex key

11. Baseplate bolts

12. Worklight

3. ASSEMBLY

Before any work on the power tool, remove

the battery.

The battery must be charged before ﬁrst

use.

Inserting the battery into the machine (Fig. A, F)

Ensure that the exterior of the battery is

clean and dry before connecting to the

charger or machine.

1. Insert the battery (4) into the base of the machi-

ne as shown in Fig. F.

2. Push the battery further forward until it clicks

into place.

Removing the battery from the machine (Fig. A, F)

1. Push the battery unlock button (5)

2. Pull the battery out of the machine like shown

in Fig. F.

Replacing the saw blade (Fig. A, C)

When mounting the saw blade, wear

protective gloves. Danger of injury when

touching the saw blade.

Only use saw blades that correspond with

the characteristic data given in the

operating instructions.

Mounting the saw blade

Make sure the blade holder is free of material

debris (such as splinters of wood or metal).

1. Turn the clamping lever (9) as far to the left as

possible and hold it in this position.

2. Insert the saw blade in the chuck (8). Check

that the saw blade is securely ﬁxed and that the

teeth are pointing downwards.

3. Let go of the clamping lever. Check whether the

saw blade is locked in place.

Make sure to use the right sawblade for the corres-

ponding material. Included with the machine is a

coarse sawblade for wood and a ﬁne sawblade for

metal and plastics.

Removing the saw blade

1. Turn the clamping lever (9) as far to the left as

possible and hold it in this position.

2. Remove the saw blade from the chuck (8).

3. Let go of the clamping lever.

4. OPERATION

Switching the machine on/off (Fig. A)

The on/off switch (2) is used for activating the

machine and adjusting speed.

• To start the machine, press and hold the lock-

off button (1) and press the on/off switch (2).

• The further the on/off switch (2) is being

pushed, the faster the blade will move. The

required speed depends on the material and

can be determined by practical testing.

•

To stop the machine, release the on/off switch (2).

Adjusting the base plate (Fig. B)

Due to its movability, the baseplate (7) angle

adapts to the workpiece. Furthermore, the length

of the baseplate can be adjusted depending on the

required sawing depth.

1. Loosen the baseplate boults (11) using the hex

key (10) provided.

2. Adjust the baseplate (7).

3. Tighten the baseplate bolts (11) using the hex

key (10) provided. It is possible to store the hex

key onto the machine, as shown on Fig. B.

Plunge cutting (Fig. D)

Plunge cutting may only be used on soft materials

such as wood, aerated concrete, gypsum plaster

boards, etc. However, this requires a certain practi-

se and is only possible with short saw blades.

Place the saw onto the workpiece and switch it on.

2. Ensure that the bottom edge of the footplate

rests on the workpiece surface as shown.

3. Slowly saw into the workpiece at an angle, mo-

ving the saw to a vertical position and continue

to saw along the cutting line.

4. Switch the saw off and lift off the workpiece

when the work is complete.

Flush cutting (Fig. E)

Elastic bi-metal saw blades allow you to saw

protruding objects (e,g, water pipes, iron bars, etc,)

nearby the wall.

1. Apply the saw blade directly to the wall and

bend slightly so that the footplate rests against

the wall. Pay attention that the saw blade

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc RS501DC in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vonroc RS501DC Manual

Product: