778542

Vonroc RH502AC Manual

7
Zoom out
Zoom in
Previous page
1/64
Next page
EN
7
WWW.VONROC.COM
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work patterns.
DESCRIPTION
The numbers in the text refer to the diagrams on
page 2-3.
1. Left/right rotation switch
2. On/Off switch
3. Chuck
4. Lock-on button
5. Function selection switch
6. Auxiliary grip
7. Locking sleeve
8. Depth stop ruler
9. Depth stop button
10. Keyed chuck with SDS shank
11. Chuck key
3. ASSEMBLY
Before assembly, always switch off the
machine and remove the mains plug from
the mains.
Mounting and removing the accessory (Fig. B)
Caution: drills and chisels can get very hot.
Do not use blunt drill bits or chisels.
Immediately sharpen or replace blunt drill
bits or chisels.
Mounting
Insert the accessory into the chuck (3) until a click
can be heard. If needed rotate the accessory a little
to ensure the keyway in the bit fits the chuck well.
Do not slide the locking sleeve (7) to the
rear when inserting bits.
Removing
1. Slide the locking sleeve (7) to the rear.
2. Remove the accessory from the chuck (3).
3. Release the locking sleeve (7).
Optional keyed chuck (Fig. A)
Only use the optional keyed chuck in drilling
mode! The function selector switch (5) must
be set to “drilling mode” (As shown in fig. D
function A).
1. Insert the keyed chuck with SDS shank (10)
into the chuck (3) until a click can be heard. If
needed rotate the keyed chuck a little to ensure
the keyway in the bit fits the chuck well.
2. Open the keyed chuck (10) with the chuck key
(11) by turning the rear sleeve counterclockwi-
se and insert the bit into the chuck opening.
4. Tighten the keyed chuck (10) with the chuck
key (11) by turning the rear sleeve clockwise.
Mounting and removing the auxiliary grip (Fig. A)
Mounting
1. Loosen the auxiliary grip (6) by turning it counter-
clockwise.
2. Mount the auxiliary grip (6) by sliding it over the
chuck (3).
3. Turn the auxiliary grip (6) to the required position.
4. Tighten the auxiliary grip (6) by turning it
clockwise.
Removing
1. Loosen the auxiliary grip (6) by turning it coun-
terclockwise.
2. Remove the auxiliary grip (6).
3. Tighten the auxiliary grip (6) by turning it
clockwise.
Mounting and setting depth stop (Fig. A)
1. The depth stop ruler (8) can be added to the auxi-
liary grip (6) by pushing the dept stop button (9).
2. Keep pushing the depth stop button (9) and
insert the depth stop ruler (8) through the hole
on the side handle ring.
3. Slide the ruler (8) to the desired depth.
4. Loosen the depth stop button (9).
4. OPERATION
Hammer drills require very little operator
pressure. Excessive pressure on the tool
can lead to unnecessary overheating of the
motor, and burning of the driven tool. It also
may happen the drill bit deforms and
cannot be removed from the machine again.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc RH502AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc RH502AC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 8.34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info