819197

Vonroc PW508DC Manual

9
Zoom out
Zoom in
Previous page
1/96
Next page
EN
9
WWW.VONROC.COM
• Fully charging the 2Ah battery may take up to
60 minutes.
• Fully charging the 4Ah battery may take up to
120 minutes.
After the battery is fully charged remove the charg-
er plug from the outlet and remove the battery from
the charger.
When the machine is not being used over
alonger period of time it is best to store the
battery in charged condition.
4. OPERATION
Connecting the watersupply
This unit is to be used with acold-water
source only!
The pressure washer must only be used
with clean water; use of unfiltered water or
corrosive chemicals will damage the
pressure washer.
Ensure that you have asuitable water
supply to feed the pressure washer. Check
that all connections are tight and there are
no leaks in the hose.
You can enable the water supply via awater tank
(or pond, rain barrel, etc.) or via awater tap.
Water tank (water suction function) (Fig. E1)
Clean the suction filter (9) at regular
intervals, and check it for damage.
Otherwise, its function can be impaired.
When water is supplied via awater tank, pond, rain
barrel, etc. , the assembled suction hose (7) must
be used. Only clear fresh water may be used.
1. Connect the assembled suctionhose (7) to the
pressure washer, place the hose connector (5)
on to the water inlet (4).
2. Lower the suction filter (9) into water. Ensure
there are no obstructions around the suction fil-
ter (9). Move the float ball (8) in such away that
the suction filter (9) does not touch the water
bottom. The suction filter (9) must be placed at
least 20 cm from the water bottom to prevent
the suction of sand. When using awater tank,
rain barrel or bucket, you can secure the hose
by using the bucket clamp (12).
3. Check that the hose has no kinks in it.
4. The pressure washer is now ready for use.
Water tap (Fig. E2)
Use the device on adomestic water
connection with maximum pressure of
5bar.
The supply tap should be fully open.
1. Ensure that you have asuitable water supply to
feed the pressure washer.
2. Connect the water supply hose (not included) to
to the water inlet (4).
3. Connect the water supply hose (not included) to
the water supply.
4. Turn on water and heck that the hose has no
kinks in it.
5. The pressure washer is now ready for use.
Switching the pressure washer on/off (Fig. A)
The motor of this pressure washer will NOT
run. It will only operate when the trigger is
squeezed.
Before starting make sure the pressure
washer is connected to awater source. Dry
running will damage the pressure washer!
• To start the pressure washer, press and hold the
release button (11) and press the switch lever
(10).
• To stop the pressure washer, release the switch
lever (10).
Adjusting the nozzle (Fig. F)
Water may be sprayed out of the nozzle (3) either
linearly or in afan shape. Turn on the pressure first,
and then adjust the nozzle (3).
Using detergents (Fig G, A)
The detergent bottle (13) will allow you to apply
many forms of liquid detergent onto the work
surface.
1. Remove the detergent dispenser of the deter-
gent reservoir and fill with liquid detergent only.
Do not put any water into the reservoir. The de-
tergent bottle (13) will mix water and detergent
automatically.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc PW508DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc PW508DC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 11.87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info