764179

Vonroc PW503AC Manual

9
Zoom out
Zoom in
Previous page
1/56
Next page
EN
9
WWW.VONROC.COM
shown in Fig. C3.
5. Check gauze filter (3) is clear of any blockage
and assemble on the machine as shown in Fig.
C4.
6. Connect the water supply hose.
7. Check that the hose has no kinks in it.
8. Turn on water and check for leaks.
9. Squeeze trigger to allow air to be expelled
though the pump and hoses, lock trigger as
shown in Fig. C5.
10. Plug in machine and turn on switch (2).
11. Unlock trigger as shown in Fig. C5 and use the
pressure washer.
Patio cleaner (Fig. A)
The patio cleaner (15) is ideally suited for the cle-
aning of floor and wall surfaces made of different
materials such as wood, plastic, concrete, tiles,
and natural stone.
1. Connect the patio cleaner lance to the patio
cleaner (15) as shown in figure A.
2.
Connect the lance extension (12) and the adapter
(19) to the patio cleaner (15).
3. Connect the set to the spray gun (9).
Shut down (Fig. A, C)
Never disconnect the high pressure hose
(16) from the machine while the system is
still pressurized.
ALWAYS turn off the unit’s motor BEFORE
turning off the unit’s water supply. Serious
damage could occur to the motor if the unit
is run without water.
1. Turn off the motor (push switch (2) to the off
position).
2. Unplug the unit from the power source.
3. Turn off the water supply.
4. Press the trigger of the gun (9) to depressurize
the system.
5. Disconnect the garden hose from the pressure
washer.
6. Engage the gun safety lock as shown in Fig. C5.
7. Wipe all surfaces of the unit with a damp clean
cloth.
Water supply
This unit is to be used with a cold-water
source only!
• Ensure that you have a suitable water supply
to feed the pressure washer. Check that all
connections are tight and there are no leaks in
the hose.
• The supply tap should be fully open (do not turn
on the pressure washer yet).
• Now depress the trigger (unlock trigger lock
first) to let water pass through the unit and
expel any air.
• Turn on the pressure washer, once all the air
has been expelled and water has reached the
end of the lance.
Adjusting the nozzle (Fig. A, D)
• Water may be sprayed out of the nozzle either
linearly or in a fan shape. Turn on the pressure
first, and then adjust the nozzle.
Adjusting the working pressure (Fig. A, E)
The working pressure can be adjusted by turning
the sleeve on the end of the nozzle.
• Turn the sleeve clockwise to increasing the
working pressure.
• Turn the sleeve counter-clockwise to reduce the
working pressure.
Using detergents (Fig. A, E1)
The built-in detergent dispenser will allow you
to apply many forms of liquid detergent onto the
work surface. Detergent application happens at
low-pressure only.
• Connect the adjustable nozzle (10) to the gun
(9).
• Adjust the nozzle (10) to low pressure setting
'' ''.
• Remove the cap on the detergent reservoir
(14) and fill with liquid detergent only. Do not
put any water into the reservoir. The pressure
washer will mix water and detergent automati-
cally. When finished applying the detergent to
the work surface, it is possible to spray off the
detergent by using the high pressure setting
'' ''. In high-pressure mode, the pressure
washer will not dispense detergent.
Adjusting the detergent rate (Fig. A, E2)
To adjust the rate detergent is mixed with the water
you can turn the detergent knob (17).
• Turn left to decrease the amount of detergent
added.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc PW503AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc PW503AC in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 4,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info