819205

Vonroc PM508DC Manual

10
Zoom out
Zoom in
Previous page
1/116
Next page
10
EN
WWW.VONROC.COM
Fitting the polishing bonnet (Fig. D)
Make sure to use the right polishing bonnet
for the corresponding material. To
determine which bonnet you need, we
recommend to read and understand all
information supplied with your polish or
wax.
Use undamaged and clean polishing
accessories only.
1. Hold the machine upside down.
2. Place the polishing bonnet (4, 5) onto the pad
(3) as shown in Fig. D. Make sure the bonnet is
fitted securely.
Removing the polishing bonnet
1. Hold the machine upside down.
2. Remove the polishing bonnet (4, 5) by pulling
the bonnet edges over and off the pad.
4. OPERATION
Always start and stop the polisher on or
against the surface.
Switching on (Fig. A)
1. Firmly hold the machine with both hands, using
both of the handles (2).
2. To switch on the machine, Press the on/off
button (1).
Switching off (Fig. A)
1. To switch off the machine, Press the on/off
button (1).
2. Wait until the pad stops rotating before lifting
the polisher from the surface.
3. Remove battery from machine
Adjustable handle (Fig. E)
The machine features an adjustable handle that
can be adjusted in two positions. Pull the handle
out and turn it 90 degrees upwards.
Spend some time finding the position that is right
for the job. The rotatable handle makes work more
ergonomically correct.
Do not adjusted the handles during use.
Hints for optimum use
• For best results, the surface should be clean
and dry.
• Do not apply polish directly to car. Apply a small
amount of polish on the polishing bonnet.
• Do not apply too much pressure on the machi-
ne. Let the machine do the work.
• Begin by polishing larger flat surfaces, such as
the roof and hood. Use a sweeping motion in a
criss-cross pattern.
• Once flat surfaces have been covered, polish
curved surfaces.
• For hard to reach areas, such as the underside
of bumpers or side mirrors, apply polish by
hand.
• Do not use any type of abrasive cleanser as it
may damage or scratch the surface.
5. MAINTENANCE
Before cleaning and maintenance, always
switch off the machine and remove the
battery pack from the machine.
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that the
ventilation openings are free of dust and dirt. Re-
move very persistent dirt using a soft cloth moiste-
ned with soapsuds. Do not use any solvents such
as gasoline, alcohol, ammonia, etc. Chemicals such
as these will damage the synthetic components.
ENVIRONMENT
Faulty and/or discarded electrical or
electronic apparatus have to be collected at
the appropriate recycling locations.
Only for EC countries
Do not dispose of power tools into domestic waste.
According to the European Guideline 2012/19/
EU for Waste Electrical and Electronic Equipment
and its implementation into national right, power
tools that are no longer usable must be collected
separately and disposed of in an environmentally
friendly way.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc PM508DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc PM508DC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 10.44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info