Manual Vonroc PM508DC (page 7 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish)

819205

Zoom out

Zoom in

1/116

WWW.VONROC.COM

accessory could snag your clothing, pulling the

accessory into your body.

n) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the hou-

sing and excessive accumulation of powdered

metal may cause electrical hazards.

o) Do not operate the power tool near ﬂammable

materials. Sparks could ignite these materials.

p) Do not use accessories that require liquid cool-

ants. Using water or other liquid coolants may

result in electrocution or shock.

q) Do not allow any loose portion of the polishing

bonnet or its attachment strings to spin freely.

Tuck away or trim any loose attachment strings.

Loose and spinning attachment strings can

entangle your ﬁngers or snag on the workpiece.

r) Do not press the spindle lock until the tool stops.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or any

other accessory. Pinching or snagging causes rapid

stalling of the rotating accessory which in turn

causes the uncontrolled power tool to be forced in

the direction opposite of the accessory’s rotation at

the point of the binding. For example, if an abrasive

wheel is snagged or pinched by the workpiece, the

edge of the wheel that is entering into the pinch

point can dig into the surface of the material cau-

sing the wheel to climb out or kick out. The wheel

may either jump toward or away from the operator,

depending on direction of the wheel’s movement

at the point of pinching. Abrasive wheels may also

break under these conditions. Kickback is the

result of power tool misuse and/or incorrect opera-

ting procedures or conditions and can be avoided

by taking proper precautions as given below.

a) Maintain a ﬁrm grip on the power tool and po-

sition your body and arm to allow you to resist

kickback forces. Always use auxiliary handle,

if provided, for maximum control over kickback

or torque reaction during start-up. The operator

can control torque reactions or kickback forces,

if proper precautions are taken.

b) Never place your hand near the rotating acces-

sory. Accessory may kickback over your hand.

c) Do not position your body in the area where po-

wer tool will move if kickback occurs. Kickback

will propel the tool in direction opposite to the

wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving blade or

toothed saw blade. Such blades create frequent

kickback and loss of control.

SAFETY WARNINGS FOR BATTERY

a) Do not open the battery. Danger of shortcircui-

ting.

b) Protect the battery against heat, e. g., against

continuous intense sunlight, ﬁre, water, and

moisture. Danger of explosion.

c) In case of damage and improper use of the bat-

tery, vapours may be emitted. Ventilate the area

and seek medical help in case of complaints.

The vapours can irritate the respiratory system.

d) Use the battery only in conjunction with your

Vonroc product. This measure alone protects

the battery against dangerous overload.

e) The battery can be damaged by pointed objects

such as nails or screwdrivers or by force

applied externally. An internal short circuit can

occur and the battery can burn, smoke, explode

or overheat.

SAFETY WARNINGS FOR CHARGER

Intended use

Charge only CD801AA and CD803AA type rechar-

geable Battery packs with the charger. Other types

of batteries may burst causing personal injury and

damage.

a) The appliance is not to be used by persons

(including children) with reduced physical, sen-

sory or mental capabilities, or lack of experien-

ce and knowledge, unless they have been given

supervision or instruction.

b) Children being supervised not to play with the

appliance.

c) Do not recharging non-rechargeable batteries!

d) During charging, batteries must be placed in

the well ventilated area!

Electrical safety

Always check that the voltage of the power

supply corresponds to the voltage on the

rating plate.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc PM508DC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 10.44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vonroc PM508DC Manual

Product: