764131

Vonroc PM502AC Manual

6
Zoom out
Zoom in
Previous page
1/28
Next page
6
EN
WWW.VONROC.COM
Replacing the whisk (Fig. A)
Before assembly, always switch off the
machine and remove the mains plug from
the mains.
Use only whisks conform the specified diameter.
Always use a whisk that is suitable for the material
to be mixed/stirred. Using an unsuitable mixer bar
can unnecessarily overload both the machine and
yourself.
Mounting the whisk
1. Screw the assembled whisk into the tool holder
(5) in clockwise direction as far as possible.
2. Tighten the whisk into the tool holder using
the supplied spanners. To do so, hold the tool
holder (5) using one of the supplied spanners,
and use the second spanner to tighten the
assembled whisk.
Removing the whisk
1. Loosen the assembled whisk using the supplied
spanners. To do so, hold the tool holder (5)
using one of the supplied spanners, and use the
second spanner to loosen the assembled whisk.
2. Unscrew the whisk from the tool holder (5) in
anti-clockwise direction.
4. OPERATION
Switching on and off (Fig. A)
• To switch on the tool, press and hold the on/off
switch (1).
• If you release the on/off switch, the tool will be
switched off.
You can lock the on/off switch by pressing the
on/off switch (1) and then button (3). The switch
lock can be released by briefly pressing the on/off
switch.
Gear selection (Fig. B)
Two mechanical speed ranges can be selected with
the gear selector switch (4):
Gear 1 180-400/min
Gear 2 300-700/min
The necessary gear depends on the type of the
material mixed and it is recommended to verify it
by a practical test.
Speed adjustment (Fig. B)
The required speed can be adjusted by using the
Speed adjustment wheel (3). Also during operation
the rotational speed can be adjusted.
•
To increase the speed, turn the Speed adjustment
knob (3) clockwise.
• To decrease the speed, turn the Speed adjustment
knob (3) anti-clockwise.
The required speeds depends on the material
and can be determined by practical testing.
Optimum use
•
For materials with low viscosity, e.g. emulsion
paint, varnishes, adhesive, grouting compound
and cement slurry, a stirrer whisk with a so-called
left-hand spiral is recommended for optimum
use. With a left-hand spiral, the material is moved
from the top downwards and the stirrer whisk is
pushed upwards. Materials with low viscosity are
mixed in a way which minimises splattering, so a
low speed is recommended (gear 1).
•
For materials with high viscosity, e.g. plaster,
concrete, cement, screed, filler and epoxy resin, a
stirrer whisk with a so-called right-hand spiral is
recommended for optimum use. With a right-hand
spiral, the material is moved from the bottom
upwards and the stirrer whisk is pulled downwards
(working its way into the mixture). Materials with
high viscosity are mixed thoroughly, so a high
speed is recommended (gear 2).
• For optimum results, move the power tool in an
up and down motion while mixing.
• It is recommended to clean the whisk after use,
for example by stirring the whisk in a bucket
filled with water.
5. MAINTENANCE
Always disconnect the machine from the
main power supply before carrying out any
maintenance work.
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that the
ventilation openings are free of dust and dirt.
Remove very persistent dirt using a soft cloth
moistened with soapsuds. Do not use any solvents
such as gasoline, alcohol, ammonia, etc. Chemicals
such as these will damage the synthetic components.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc PM502AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc PM502AC in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info